Danfoss D9h Operating Manual page 163

VLT® AutomationDrive FC 302
Operating Guide
FC 302
- Mains with disconnect [mm
- Mains with fusible disconnect [mm
- Mains with contactor [mm
2
- Mains [mm (AWG)]
Drive module power loss at 400 V [W]
Drive module power loss at 460 V [W]
Drive efficiency
(2)
Output frequency [Hz]
(4)
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
PHF overtemperature trip [°C (°F)]
Line reactor overtemperature trip [°C (°F)]
dU/dt filter overtemperature trip [°C (°F)]
Sine-wave filter overtemperature trip [°C (°F)]
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These
1
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimension-
ing of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control card power
consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-efficiency-direc-
tive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each
add only 4 W.
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficien-
2
cy class, see the Ambient Conditions section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
See also Input Power Option Losses section.
3
If using an output filter, the output frequency is limited further. See
4
Table 103: Electrical Data, Mains Supply 3x380–500 V AC
FC 302
High/normal overload
High overload=150% or 160% torque for a duration of 60 s.
Normal overload=110% torque for a duration of 60 s.
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [hp]
Typical shaft output at 500 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 400 V) [A]
Intermittent (60 s overload) (at 400 V) [A]
Continuous (at 460/500 V) [A]
Danfoss A/S © 2021.10
2
(AWG)]
2
(AWG)]
2
(AWG)]
(1)(2)(3)
(1)(2)(3)
N160
2x185 (2x350 mcm) 2x185 (2x350 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
3093 4116
2872 3569
0.98
0–590
110 (230)
80 (176)
145 (293)
150 (302)
150 (302)
150 (302)
10.3.1 Motor Output (U, V, W).
N315
HO NO
315 355
450 500
355 400
E5h
600 658
900 724
540 590
Specifications
N200 N250
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
4039 5137 5005
3575 4566 4458
0.98 0.98
0–590 0–590
110 (230) 110 (230)
80 (176) 80 (176)
145 (293) 145 (293)
150 (302) 150 (302)
150 (302) 150 (302)
150 (302) 150 (302)
N355 N400
HO NO HO
355 400 400
500 600 550
400 500 500
E5h
658 745 695
987 820 1043
590 678 678
AQ262139143212en-000301 / 130R0879 | 163
6674
5714
NO
450
600
530
E5h
800
880
730