Power Jumper Contacts/Field Supply; Figure 6: Power Jumper Contacts; Table 5: Legend For Figure "Power Jumper Contacts - WAGO -I/O-SYSTEM 750 Series Manual

24 Device Description
Pos: 24.11 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Anschlüsse/Leistungskontakte/Feldversorgung - Überschrift 3 @ 6\mod_1256294692864_21.docx @ 43664 @ 3 @ 1
4.2.2

Power Jumper Contacts/Field Supply

Pos: 24.12.1 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Vorsicht/Vorsicht: Verletzungsgefahr durch scharfkantige Messerkontakte! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos: 24.12.2 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Anschlüsse/Leistungskontakte 2 LK (Messer/Leistungskontakte 2 LK (Messer/Feder) - Einleitung @ 15\mod_1371721641099_21.docx @ 123714 @ @ 1
The I/O module 753-661/000-003 has 2 self-cleaning power jumper contacts that
supply and transmit power for the field side. The contacts on the left side of the
I/O module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 24.12.3 /Serie 753 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Anschlüsse/Leistungskontakte/Feldversorgung 2 LK (Messer/Feder) PROFIsafe - Abbildung @ 20\mod_1411564875536_21.docx @ 164574 @ @ 1

Figure 6: Power Jumper Contacts

Pos: 24.12.4 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Anschlüsse/Leistungskontakte 2 LK (Messer/Leistungskontakte 2 LK (Messer/Feder) - Legende @ 15\mod_1371721352500_21.docx @ 123710 @ @ 1

Table 5: Legend for Figure "Power Jumper Contacts"

Contact
1
2
3
4
Pos: 24.12.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: Maximaler Strom Leistungskontakte 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos: 24.12.6 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Hinweis/Hinweis: Potentialeinspeiseklemme für Erde einsetzen! (keine LK für Erde) @ 3\mod_1226499037468_21.docx @ 25023 @ @ 1
Type
Spring contact Potential transmission (U
Spring contact Potential transmission (0 V) for field supply
Blade contact
Blade contact
753-661/000-003 4FDI 24V PROFIsafe V2 iPar
Function
Potential feed-in (0 V) for field supply
Potential feed-in (U
v
Version 1.4.0, valid from HW/SW Version 01/02
WAGO-I/O-SYSTEM 750
) for field supply
v
) for field supply
Manual