Power Jumper Contacts/Field Supply; Figure 3: Power Jumper Contacts; Table 4: Legend For Figure "Power Jumper Contacts - WAGO -I/O-SYSTEM 750 Manual

WAGO-I/O-SYSTEM 750
753-540 4DO 230 V AC
Pos : 28 /Serie 750 ( WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üss e/Leistungs kontakte/F el dvers orgung - Übersc hrift 3 @ 6\mod_1256294692864_21.doc x @ 43664 @ 3 @ 1
3.2.2

Power Jumper Contacts/Field Supply

Pos : 29.1 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Vorsic ht/Vorsicht: Verl etz ungsgefahr durc h s charfkantige M ess er kontakte! @ 6\mod_1256193279401_21.doc x @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos : 29.2 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üsse/Leistungs kontakte 2 LK (Mess er/F eder) - Einl eitung @ 15\mod_1371721641099_21.doc x @ 123714 @ @ 1
The I/O module 753-540 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos : 29.3 /Serie 753 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üsse/Leistungs kontakte/F eldvers orgung 2 LK (Mes ser/F eder) - Abbildung @ 17\mod_1381924880242_21.doc x @ 134239 @ @ 1

Figure 3: Power Jumper Contacts

Pos : 29.4 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üsse/Leistungs kontakte 2 LK (Mess er/F eder) - Leg ende @ 15\mod_1371721352500_21.doc x @ 123710 @ @ 1

Table 4: Legend for Figure "Power Jumper Contacts"

Contact
1
2
3
4
Pos : 29.5 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Achtung/Achtung: M axi mal er Strom Leistungs kontakte 10 A @ 3\mod_1226499143500_21.doc x @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos : 29.6 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Hinweis/Hi nweis: Potenti alei ns peis ekl emme für Erde ei nsetzen! ( kei ne LK für Erde) @ 3\mod_1226499037468_21.doc x @ 25023 @ @ 1
Manual
Version 1.1.0
Type
Spring contact Potential transmission (U
Spring contact Potential transmission (0 V) for field supply
Blade contact
Blade contact
Function
Potential feed-in (0 V) for field supply
Potential feed-in (U
v
Device Description
) for field supply
v
) for field supply
17