Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 69

Pos : 162.1 /Anleitungen/El ektr oni k/FU und Starter/2. M ontage und Installation/Elektrischer Ansc hl uss/SK 1xxE, SK 2xxE, SK xxxE-FDS/Steuer teil/D etails Steueransc hlüs se (Samml ung)/Details Steueransc hlüs se_00_T abellenkopf_[SK 1xxE, SK 2xxE] @ 7\mod_1435561812889_388.doc x @ 228818 @ @ 1
Meaning, Functions
Terminal
No.
Designation
Pos : 162.2 /Anleitungen/El ektr oni k/FU und Starter/2. M ontage und Installation/Elektrischer Ansc hl uss/SK 1xxE, SK 2xxE, SK xxxE-FDS/Steuer teil/D etails Steueransc hlüs se (Samml ung)/Details Steueransc hlüs se_01_DOUT [SK 1x0E, SK 2xxE] @ 7\mod_1435562956782_388.doc x @ 229138 @ @ 1
Digital outputs
1 DOUT1
3 DOUT2
Pos : 162.3 /Anleitungen/El ektr oni k/FU und Starter/2. M ontage und Installation/Elektrischer Ansc hl uss/SK 1xxE, SK 2xxE, SK xxxE-FDS/Steuer teil/D etails Steueransc hlüs se (Samml ung)/Details Steueransc hlüs se_01_DOUT _Ergänz ung [SK 2xxE] @ 7\mod_1435562960093_388.doc x @ 229170 @ @ 1
Notes:
Size 4: Max. load 50 mA
SK 2x5E: Voltage level depending on input voltage level (18 – 30 V DC)
Pos : 162.4 /Anleitungen/El ektr oni k/FU und Starter/2. M ontage und Installation/Elektrischer Ansc hl uss/SK 1xxE, SK 2xxE, SK xxxE-FDS/Steuer teil/D etails Steueransc hlüs se (Samml ung)/Details Steueransc hlüs se_02_AIN [SK 1x0E, SK 2x0E] @ 7\mod_1435563256730_388.doc x @ 229266 @ @ 1
Analogue inputs
11
10V REF
14
AIN1+
16
AIN2+
40
GND
Pos : 162.5 /Anleitungen/El ektr oni k/FU und Starter/2. M ontage und Installation/Elektrischer Ansc hl uss/SK 1xxE, SK 2xxE, SK xxxE-FDS/Steuer teil/D etails Steueransc hlüs se (Samml ung)/Details Steueransc hlüs se_02_AIN_Ergänzung [SK 2x0E] @ 7\mod_1435563260457_388.doc x @ 229298 @ @ 1
NOTICE: SK 200E and SK 210E: Terminal 12 must be used instead of terminal 40 (AGND/0V)
Pos : 162.6 /Anleitungen/El ektr oni k/FU und Starter/2. M ontage und Installation/Elektrischer Ansc hl uss/SK 1xxE, SK 2xxE, SK xxxE-FDS/Steuer teil/D etails Steueransc hlüs se (Samml ung)/Details Steueransc hlüs se_03_DIN [SK 2xxE] @ 7\mod_1435562625904_388.doc x @ 229010 @ @ 1
Digital inputs
21
DIN1
22 DIN2
23 DIN3
24 DIN4
Pos : 162.7 /Anleitungen/El ektr oni k/FU und Starter/2. M ontage und Installation/Elektrischer Ansc hl uss/SK 1xxE, SK 2xxE, SK xxxE-FDS/Steuer teil/D etails Steueransc hlüs se (Samml ung)/Details Steueransc hlüs se_04_TF [SK 1xxE, SK 2xxE] @ 7\mod_1435563263847_388.doc x @ 229330 @ @ 1
PTC resistor input
38
TF+
39
TF-
Pos : 162.8 /Allgemein/Allgemei ngültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265495 @ @ 1
BU 0200 en-3118
Description / Technical data
Meaning
Signalling of device operating statuses
24 V DC
With inductive loads: Provide protection
via free-wheeling diode!
Digital output 1
Digital output 2
Actuation of device by external controller, potentiometer or the like.
Resolution 12Bit
U= 0 ...10 V, R =30 kΩ
i
I= 0/4 ... 20 mA
Burden resistance (250 Ω) via DIP switch
AIN1/2
Maximum permissible voltage at
analogue input: 30 V DC
+ 10 V Reference voltage
Analogue input 1
Analogue input 2
Reference potential GND
Actuation of device via an external controller, switch or the like, connection of HTL
transmitter (DIN2 and DIN3 only)
as per EN 61131-2, type 1
Low: 0-5 V (~ 9.5 kΩ)
High: 15-30 V (~ 2.5 - 3.5 kΩ)
Scan time: 1 ms
Reaction time: 4 - 5 ms
Digital input 1
Digital input 2
Digital input 3
Digital input 4
Monitoring of motor temperature using PTC
If the device is installed near the motor, a
shielded cable must be used.
PTC resistor input
PTC resistor input
2 Assembly and installation
Parameter
No. Function of factory setting
Maximum load 20 mA
P434 [-01] Fault
P434 [-02] Fault
Matching of the analogue signals is performed via P402 and
P403.
+ 10 V Reference voltage: 5 mA not short-circuit resistant
11
40
10 kΩ
14
- -
P400 [-01] Setpoint frequency
P400 [-02] No function
- -
Input capacitance
10 nF (DIN1, DIN 4)
1.2 nF (DIN 2, DIN 3)
DIN 2 and DIN 3 double allocation
Min.: 250 Hz, Max.: 205 kHz
P420 [-01] ON right
P420 [-02] ON left
P420 [-03] Fixed frequency 1 ( P465[-01])
P420 [-04] Fixed frequency 2 ( P465[-02])
The input is always active. In order to make the device
operational, a temperature sensor must be connected or both
contacts must be jumpered.
- -
- -
69