Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 200

NORDAC FLEX (SK 200E ... SK 235E) – Users Manual for Frequency Inverters
Pos : 525 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P541 – Rel ais und digital e Ausg äng e s etz en [SK 2xxE, SK 2xxE-FDS] @ 2\mod_1346932170278_388.doc x @ 43248 @ @ 1
Set relay
P541
(set digital output)
0000 ... FFF (hex) This function provides the opportunity to control the relay and the digital outputs independently of
the frequency inverter status. To do this, the relevant output must be set to the function "External
{ 0000 }
control".
This function can either be used manually or in combination with a bus control.
Bit 0 = Digital output 1
Bit 1 = Bus/AS-i Out Bit 0
Bit 2 = Bus/AS-i Out Bit 1
Bit 3 = Bus/AS-i Out Bit 2
Bit 4 = Bus/AS-i Out Bit 3
Bit 5 = Bus/An/Dig Out Bit 4,
Changes which are made to the settings are not saved in the EEPROM. After "Power ON" of the
frequency inverter, the parameter is therefore in the default setting.
Setting of the value via ...
BUS:
SimpleBox:
ParameterBox:
Pos : 526 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P542 – Analogausgang s etz en [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 2\mod_1346932170902_388.doc x @ 43272 @ @ 1
P542 Set analogue output
[-01]
[-02] (Set analogue output)
[-01] = First IOE, AOUT of the first I/O extension (SK xU4IOE)
0.0 ... 10.0 V
[-02] = Second IOE, AOUT of the second I/O extension (SK xU4IOE)
{ all 0.0 }
only with The analogue output of the FI can be set with this function, independently of the actual operating
SK CU4-IOE or state. To do this, the relevant analogue output must be set to the function "External control"
SK TU4-IOE (P418 = 7).
This function can either be used manually or in combination with a bus control. The value set here
will, once confirmed, be produced at the analogue output.
Changes which are made to the settings are not saved in the EEPROM. After "Power ON" of the
frequency inverter, the parameter is therefore in the default setting.
Pos : 527 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265495 @ @ 1
200
"Bus/Analogue /Digital Out Bit 4"
Bits 8-11
0000
Min. value
0
1111
Max. value
F
The corresponding hex value is written into the parameter, thereby setting the
relay and digital outputs.
The hexadecimal code is entered directly when the SimpleBox is used.
Each individual output can be separately called up in plain text and activated.
Bit 6 = Bus/An/Dig Out Bit 5,
"Bus/Analogue /Digital Out Bit 5"
Bit 7 = Bus digital output 7
Bit 8 = Bus digital output 8
Bit 9 = Bus statusword Bit10
Bit 10 = Bus statusword Bit13
Bit 11 = Digital output 2
Bits 7-4 Bits 3-0
0000 0000
0 0
1111 1111
F F
S
Binary
hex
Binary
hex
S
BU 0200 en-3118