Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 279

Pos : 767 /Allgemein/Steuer module/Stichwortverzeic hnis @ 0\mod_1317978518730_388.doc x @ 4101 @ @ 1
Key word index
=== Ende der Liste für T extmar ke Stichwortverzeic hnis ===
3
3-Wire-Control ............................................. 177
A
Absolute minimum frequency (P505) .......... 189
Acceleration time (P102) ............................ 139
Actual
cos phi (P725) .......................................... 213
current (P719) .......................................... 213
field current (P721) .................................. 213
frequency (P716) ..................................... 212
Speed (P717) ........................................... 212
torque current (P720) ............................... 213
voltage (P722) .......................................... 213
Actual
Mains current (P760) ............................... 220
Actual bus value 1 ... 3 (P543) .................... 201
Actual frequency processing ....................... 275
Actual values ............................................... 274
Additional parameters .................................. 187
Address........................................................ 277
Adjustment range
1/10 ......................................... 267, 270, 272
1/17 .......................................................... 271
Analog input voltage (P709) ........................ 211
Analogue input adjustment
0% (P402) ................................................ 170
100% (P403) ............................................ 171
Analogue input filter (P404) ......................... 171
Analogue output filter 1 (P418) .................... 174
Analogue output voltage (P710) .................. 211
Apparent power (P726) ............................... 213
Array parameters ......................................... 136
AS interface ................................................. 119
Assembly
SK 2xxE ..................................................... 37
ATEX .......................................... 25, 29, 44, 75
Optional ATEX modules ............................. 77
ATEX
ATEX Zone 22, Cat. 3D ............................. 76
ATEX
EU conformity declaration .......................... 81
ATEX
ATEX Zone 22, Cat. 3D ............................. 82
Automatic error acknowledgement P506 .... 189
Automatic flux optimisation .......................... 266
BU 0200 en-3118
Automatic flux optimisation (P219) ............. 152
Automatic starting (P428) ........................... 179
B
Basic parameter .......................................... 139
Boost precontrol (P215) .............................. 150
Brake chopper ............................................... 52
Brake control ....................................... 142, 145
Brake reaction time (P107) ......................... 142
Brake release time (P114) .......................... 145
Brake resistor (P556) .................................. 205
Brake resistor type (P557) .......................... 205
Braking distance ......................................... 143
Braking resistor ..................................... 52, 240
Bus
Setpoint (P546) ....................................... 202
Bus I/O In Bits ............................................. 184
Bus I/O Out Bits .......................................... 184
Bus setpoints ...................................... 202, 204
Bus status via PLC (P353) .......................... 162
C
CAN address (P515) ................................... 192
CAN bus baud rate (P514) ......................... 191
CAN master cycle (P552) ........................... 203
CANopen status (P748) .............................. 218
CE mark ...................................................... 252
Configuration level (P744) .......................... 218
conformity declaration
ATEX ......................................................... 81
Contact ........................................................ 277
Control connection ........................................ 65
Control options ........................................ 86, 89
Control terminals ..................... 67, 73, 122, 164
COPY .......................................................... 111
Copy function .............................................. 111
Copy parameter set (P101) ........................ 139
CSA ............................................................. 239
cUL .............................................................. 239
Current
DC brake (P109) ..................................... 144
phase U (P732) ....................................... 214
phase V (P733) ....................................... 214
phase W (P734) ...................................... 215
Current limit (P536) ..................................... 198
Current vector control ................................. 152
Curve setting ............................... 149, 150, 152
Key word index
279