Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 202

NORDAC FLEX (SK 200E ... SK 235E) – Users Manual for Frequency Inverters
Pos : 531 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P546 – Funktion Bus- Soll werte [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 2\mod_1346932172150_388.doc x @ 43320 @ @ 1
P546
[-01]
Function Bus setpoint
...
(Function of bus setpoint)
[-03]
0 ... 36 In this parameter, a function is allocated to the output setpoint during bus actuation.
{ [-01] = 1 } NOTE:
{ [-02] = 0 }
{ [-03] = 0 }
[-01] = Bus setpoint value 1
Possible values which can be set:
10 = Actual freq. PI monitored
11 = Torque current limit, "Torque current
12 = Torque current switch-off,
Pos : 532 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P546 – Funktion Bus- Soll werte_Ergänz ung [SK 2xxE, SK 2xxE-FDS] @ 19\mod_1506006002157_388.doc x @ 2366081 @ @ 1
Pos : 533 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P549 – Funktion Poti- Box [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 2\mod_1346932172758_388.doc x @ 43344 @ @ 1
PotentiometerBox function
P549
(PotentiometerBox function
0 ... 16 This parameter provides the possibility of adding a correction value (fixed frequency, analogue,
bus) to the current setpoint value by means of the SimpleBox/ParameterBox keyboard.
{ 0 }
The adjustment range is determined by the auxiliary setpoint value P410/411.
Pos : 534 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265495 @ @ 1
202
For further details, please refer to the relevant bus manual or the description for
(P400). (Values from 0 % ... 100 % correspond to 0000
For standardisation of the setpoint values: (please see chapter 8.9 "Standardisation
of setpoint / target values").
0 = Off
1 = Setpoint frequency (16 bit)
2 = Frequency addition
3 = Frequency subtraction
4 = Minimum frequency
5 = Maximum frequency
6 = Process controller actual value
7 = Process controller setpoint
8 = Actual frequency PI
9 = Actual freq. PI limited
limited"
"Torque current switch-off limit"
)
0 = Off
1 = Setpoint frequency, with(P509)≠ 1
control via USS is possible
[-02] = Bus setpoint value 2
13 = Current limit, "Current limited"
14 = Current Switch-off
"Current switch-off limit"
15 = Ramp time, (P102/103)
16 = Lead torque, ((P214) multiplication)
17 = Multiplication
18 = Curve travel calculator
19 = Servo mode torque
20 = BusIO InBits 0-7
21 = ...25 reserved, POSICON
31 = Digital output IOE, sets the state of DOUT
of the first IOE
32 = Analogue output IOE, sets the value
AOUT of the first IOE), condition: P418 =
Function "31"
Value must be between 0 and 100 (0
and 64
output at the analogue output.
33 = Setpoint Torque processreg., "Setpoint
torque process controller"
34 = d-correction F process
35 = d-correction Torque
36 = d-correction F+torque
2 = Frequency addition
3 = Frequency subtraction
S
... 4000
hex
[-03] = Bus setpoint value 3
). Otherwise the minimum value is
hex
S
BU 0200 en-3118
P
,)
hex
hex