Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 218

NORDAC FLEX (SK 200E ... SK 235E) – Users Manual for Frequency Inverters
Pos : 611 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P700- P799/Parameter P744 – Aus baustufe [SK 1x0E, SK 2xxE] @ 2\mod_1346932209541_388.doc x @ 43656 @ @ 1
Configuration level
P744
(Configuration level)
0000 ... FFFF This parameter displays the special devices integrated in the FI. Display is in hexadecimal code
(hex)
(SimpleBox, Bus System).
The display is in plain text when the ParameterBox is used.
High byte:
Pos : 612 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P700- P799/Parameter P744 – Aus baustufe_Teil 2/2 [SK 2xxE] @ 9\mod_1448455671379_388.doc x @ 266910 @ @ 1
00
hex
01
hex
02
hex
03
hex
Pos : 613 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P700- P799/Parameter P747 – U mrichters pannungsbereic h [SK 1x0E, SK 2xxE, SK 2xxE-FD S] @ 9\mod_1448457030116_388.doc x @ 266976 @ @ 1
P747 Inverter Volt. Range
(Inverter voltage range)
0 ... 2 Indicates the mains voltage range for which this device is specified.
0 = 100...120V
Pos : 614 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P700- P799/Parameter P748 – Status CAN open [SK 1x0E, SK 2xxE] @ 2\mod_1346932210180_388.doc x @ 43680 @ @ 1
CANopen status
P748
(CANopen status
0000 ... FFFF Shows the status of the system bus.
(hex)
or
Bit 0:
0 ... 65535
(dec)
Bit 1:
Bit 2:
Bit 3:
Bit 4:
Bit 5:
Bit 6:
Bit 7:
Bit 8:
Bit 9:
Bit 10:
Pos : 615 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265495 @ @ 1
218
No extension
Encoder
Posicon
---
1 = 200...240V
(system bus status))
24V Bus supply voltage
CANbus in "Bus Warning" status
CANbus in "Bus Off" status
System bus → Bus module online (field bus module, e.g.: SK xU4-PBR)
System bus → Additional module 1 online (I/O - module, e.g.: SK xU4-IOE)
System bus → Additional module 2 online (I/O - module, e.g.: SK xU4-IOE)
The protocol of the CAN module is
Vacant
"Bootup Message" sent
CANopen NMT State
CANopen NMT State
CANopen NMT State
Stopped
Pre- Operational
Operational
Low byte:
00 Standard I/O
hex
01 STO
hex
02 AS-i
hex
03 STO and AS-i
hex
04 Standard I/O
hex
05 STO
hex
06 AS-i
hex
07 STO and AS-i
hex
0 = CAN / 1 = CANopen
Bit 10 Bit 9
0 0
0 1
1 0
(SK 205E)
(SK 215E)
(SK 225E)
(SK 235E)
(SK 200E)
(SK 210E)
(SK 220E)
(SK 230E)
2 = 380...480V
BU 0200 en-3118