Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 134

NORDAC FLEX (SK 200E ... SK 235E) – Users Manual for Frequency Inverters
Pos : 281 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Allgemei n/Par ameter übersic ht_02_4-Steuer klemmen [SK 1x0E, SK 2xxE] @ 9\mod_1447414720702_388.doc x @ 263608 @ @ 1
Control terminals
P400 Function Setpoint inputs
P403 Adjustment: 100%
P411 Max. Freq. Auxiliary
setpoint
P414 PI control I comp.
P417 Offset analogue output
P420 Digital inputs
P428 Automatic starting
P436 Dig. out. hysteresis
P465 Fixed freq. Array
P480 Function BusIO In Bits
P483 Hyst. BusIO Out Bits
Pos : 282 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Allgemei n/Par ameter übersic ht_02_5-Z usatzpar ameter [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 9\mod_1447415583483_388.doc x @ 263641 @ @ 1
Extra parameters
P501 Inverter name
P504 Pulse frequency
P509 Control word source
P512 USS address
P515 CAN bus address
P518 Skip frequency 2
P521 Flying start Resolution
P525 Load control max
P528 Load monitoring delay
P534 Torque shutoff lim.
P537 Pulse disconnection
P541 Set relays
P546 Function Setpoint Bus
value
P552 CAN master cycle
P556 Braking resistor
P559 DC Run-on time
Pos : 283 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Allgemei n/Par ameter übersic ht_02_6-Positi oni erung [SK 2xxE, SK 2xxE-FDS] @ 9\mod_1447415705800_388.doc x @ 263674 @ @ 1
Positioning
P600 Position control
P603 Actual Pos. diff.
P607 Ratio
P610 Setpoint Mode
P613 Position
P625 Output Hysteresis
P631 Slip error. Abs./inc.
Pos : 284 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265495 @ @ 1
134
P401 Analogue input mode
P404 Analogue input filter
P412 Nom. val. process ctrl.
P415 Limit process ctrl.
P418 Funct. analogue output
P426 Quick stop time
P434 Digital output function
P460 Watchdog time
P466 Minimum freq. process
control
P481 Function BusIO Out Bits
P502 Master function value
P505 Absolute minimum freq.
P510 Setpoint source
P513 Telegram timeout
P516 Skip frequency 1
P519 Skip freq. area 2
P522 Flying start Offset
P526 Load control min
P529 Mode Load control
P535 I²t motor
P539 Output monitoring
P542 Set analogue out
P549 Pot Box function
P553 PLC setpoint
P557 Braking resistor type
P560 Parameter, saving mode
P601 Actual position
P604 Encoder type
P608 Reduction ratio
P611 Position controller P
P615 Maximum Position
P626 Comparative position
output
P640 Unit of pos. value
P402
Adjustment: 0%
P410 Min. freq. Auxiliary
setpoint
P413
PI control P comp.
P416
Ramp time PI setpoint
P419
Standard analogue
output
P427
Emerg. stop Fault
P435
Dig. out scaling
P464
Fixed frequency mode
P475
delay on/off switch
P482
Standard BusIO Out
Bits
P503
Leading function output
P506 Auto. Fault
acknowledgement
P511 USS baud rate
P514 CAN bus baud rate
P517 Skip freq. area 1
P520
Flying start
P523
Factory setting
P527
Load monitoring Freq.
P533
Factor I²t
P536
Current limit
P540 Mode phase sequence
P543 Bus - Actual value
P550 EEPROM Copy Order
P555 P - limit chopper
P558 Flux delay
P602
Actual setpoint position
P605 Absolute encoder
P609
Offset Position
P612
Pos. window
P616
Minimum Position
P630
Position slip error
BU 0200 en-3118