Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 107

Details of DIP switch S1: 5/4 and 3
Applies to devices SK 20xE, SK 21xE (without on board AS interface)
DIP Functions as per the list of digital functions (P420)
Dig 1
5 4 3
P420 [01]*
off off off
{01} "enable R"
off on off
{01} "Enable R"
on off off
{45} "3-on"
{50} "F Arr Bit0
on on off
=5Hz (P465[01])
The functions of the digital inputs are inactive (control via system bus), however, the
settings made in parameters (P420 [01 ... 04]) result in the activation of the
correspondingly parametrised input, for the functions designated with ..² in the function
list (e.g.: {11}²= "Quick stop).
off off on
P420 [01]
no function
{14} "Remote
off on on
control"
{14} "Remote
on off on
control"
{14} "Remote
on on on
control"
Explanation: (values underlined in brackets)
{curly brackets}
* Default setting
Applies to devices SK 22xE, SK 23xE (without AS interface on board)
DIP Functions as per the list of digital functions (P420)
ASi
5 4 3
In1
P480 [01]*
{01} "Enable
off off off
R"
{04} "Fixed
off on off
freq. 1"
=5Hz (P465[01])
{01} "Enable
on off off
R"
"F Arr
{51}
on on off
B1"
=10Hz (P465[02])
The functions of the digital inputs are inactive (control via system bus),
however, the settings made in parameters (P480 [01 ... 04]) result in the
activation of the correspondingly parametrised bits, for the functions
designated with ..² in the function list (e.g.: {11}²= "Quick stop).
off off on
P480 [01]
no function
{14} "Remote
off on on
control"
{14} "Remote
on off on
control"
{14} "Remote
on on on
control"
Explanation: See table above
Note: The functions of potentiometers*** P1 and P2 correspond to those of devices without an AS interface (see table above).
With DIP switches 5 and 4 in the OFF position (default setting), the digital inputs are also active. The functions then correspond
to those of devices without an AS interface (table above). In all other DIP switch combinations the functions of the digital inputs
are deactivated.
ASi OUT1 and ASi OUT2 loop the signal level (High / Low) of digital inputs 1 and 2.
Pos : 236 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265495 @ @ 1
BU 0200 en-3118
Dig 2 Dig 3
P420 [02]*
P420 [03]*
{02} "enable L"
{04} "Fixed freq1"
=5Hz (P465[01])
{26} "F
{02} "Enable L"
setpoint"***
{49} "3-off" {47} "Freq. +"
{51} "F Arr Bit1" {52} "F Arr Bit2"
=10Hz (P465[02]) =20Hz (P465[03])
P420 [03]
P420 [02]
{04} "Fixed freq1"
no function
=5Hz (P465[01])
"Encoder track A" "Encoder track B" {01} "Enable R"
{01} "Enable R" {10} "Block"
{51} "F Arr Bit1" {52} "F Arr Bit2"
=10Hz (P465[02]) =20Hz (P465[03])
= (relevant parameter / source of function), e.g.: Parameter (P420[01])
= {Function} e.g..: {01} "Enable right"
** only if present (devices without "Safe stop" function)
ASi ASi
In2 In3
P480 [02]*
P480 [03]*
{02} "Enable
{04} "Fixed
L"
freq. 1"
=5Hz (P465[01])
"Fixed
{05} "Fixed {06}
freq. 2"
freq. 3"
=10Hz (P465[02])
=20Hz (P465[03])
{02} "Enable
{47} "Freq. +"
L"
"F Arr "F Arr
{52} {53}
B2" B3"
=20Hz (P465[03]) =35Hz (P465[04])
P480 [03]
P480 [02]
"Fixed
{04}
no function
freq. 1"
=5Hz (P465[01])
"Fixed "Fixed
{04} {05}
freq. 1" freq. 2"
=5Hz (P465[01]) =10Hz (P465[02])
{01} "Enable
{47} "Freq. +"
R"
"F Arr "F Arr
{50} {51}
B0" B1"
=5Hz (P465[01]) =10Hz (P465[02])
Dig 4**
P420 [04]*
{05} "Fixed freq2"
=10Hz (P465[02])
{12} "Quit"
{48} "Freq. -"
"F Arr Bit3"
{53}
=35Hz (P465[04])
P420 [04]
{05} "Fixed freq2"
=10Hz (P465[02])
{66} "Release
brake"
"F Arr Bit3"
{53}
=35Hz (P465[04])
Functions as per the list of digital outputs
ASi ASi
In4 Out1
P480 [04]* P481 [01]*
{12} "Quit" {07} "Error"
"Fixed
{07}
{07} "Error"
freq. 4"
=35Hz
(P465[04])
{48} "Freq. -" {07} "Error"
{14} "Remote
{07} "Error"
control"
P481 [01]
{07}
"Error"
P480 [04]
"Quit"
{12}
"Fixed
{06}
{07} "Error"
freq. 3"
=20Hz (P465[03])
"Freq. -"
{48} {07} "Error"
"F Arr
{52}
{07} "Error"
B2"
=20Hz (P465[03])
4 Commissioning
Functions as per the list of
analogue functions (P400)
Poti 1*** Poti 2***
P400 [01]*
P400 [02]*
{01} "F setpoint"
{15} "Ramp"
{05} "F max" {04} "F min"
{05} "F max" {15} "Ramp"
{05} "F max" {15} "Ramp"
P400 [01] P400 [02]
{01} "F setpoint"
{15} "Ramp"
{01} "F setpoint" {05} "F max"
{01} "F setpoint" {05} "F max"
{05} "F max" {15} "Ramp"
*** only with SK 2x5E
(P434)
ASi ASi ASi
Out2 Out3 Out4
P481 [02]*
{18}
"DigIn1" "DigIn2"
"Standby"
{18}
"DigIn1" "DigIn2"
"Standby"
{18}
"DigIn1" "DigIn2"
"Standby"
{18}
"DigIn1" "DigIn2"
"Standby"
P481 [02]
{18}
"DigIn1" "DigIn2"
"Standby"
{18}
"DigIn1" "DigIn2"
"Standby"
{18}
"DigIn1" "DigIn2"
"Standby"
{18}
"DigIn1" "DigIn2"
"Standby"
107