Pos : 492 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P515 – CAN- Adr ess e_01 [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 2\mod_1346932167813_388.doc x @ 43152 @ @ 1

P515

[-01]

CAN address

...

(CAN address (system bus))

[-03]

0 ... 255

Setting of the system bus address.

dec

{ all 32

}

[-01] = Slave address, Receive address for system bus

dec

or { all 20

}

[-02] = Broadcast slave address, system bus reception address (slave)

hex

[-03] = Master address, "Broadcast master address", transmission address for system bus

NOTE: If up to four FI are to be linked via the system bus, the addresses must be set as follows  FI 1 =

32, FI 2 = 34, FI 3 = 36, FI 4 = 38.

Pos : 493 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P515 – CAN- Adr ess e_02 [SK 1x0E, SK 2xxE] @ 17\mod_1490096962359_388.doc x @ 2336244 @ @ 1

The system bus addresses should be set via DIP switches (chapter 4.3.2.2).

Pos : 494 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P516 – Aus blendfrequenz 1 @ 0\mod_1328092606664_388.doc x @ 11249 @ @ 1

Skip frequency 1

P516

(Skip frequency 1)

0.0 ... 400.0 Hz

The output frequency around the frequency value (P517) set here is not shown.

{ 0.0 }

This range is transmitted with the set brake and acceleration ramp; it cannot be continuously

supplied to the output. Frequencies below the absolute minimum frequency should not be set.

0 = Skip frequency inactive

Pos : 495 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P517 – Aus blendbereic h 1 @ 0\mod_1328092662665_388.doc x @ 11272 @ @ 1

Skip freq. area 1

P517

(Skip frequency area 1)

0.0 ... 50.0 Hz

Skip range for the >Skip frequency 1< P516. This frequency value is added and subtracted from

the skip frequency.

{ 2.0 }

Skip frequency range 1: P516 - P517 ... P516 + P517

Pos : 496 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P518 – Aus blendfrequenz 2 @ 0\mod_1328092706493_388.doc x @ 11295 @ @ 1

Skip frequency 2

P518

(Skip frequency 2)

0.0 ... 400.0 Hz

The output frequency around the set frequency value (P519) is skipped.

{ 0.0 }

This range is transmitted with the set brake and acceleration ramp; it cannot be continuously

supplied to the output. Frequencies below the absolute minimum frequency should not be set.

0 = Skip frequency inactive

Pos : 497 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P519 – Aus blendbereic h 2 @ 0\mod_1328092748353_388.doc x @ 11318 @ @ 1

Skip freq. area 2

P519

(Skip frequency area 2)

0.0 ... 50.0 Hz

Skip range for the >Skip frequency 2< P518. This frequency value is added and subtracted from

the skip frequency.

{ 2.0 }

Skip frequency range 2: P518 - P519 ... P518 + P519

Pos : 498 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265495 @ @ 1

192

(master)

BU 0200 en-3118