Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 231

Pos : 661 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E013 [SK 200E ... SK 5xxE] @ 2\mod_1347454271218_388.doc x @ 46751 @ @ 1
13.0 Encoder error
E013
13.1 Speed slip error
"Speed slip error"
13.2 Shut-down monitoring
13.5 Reserved
13.6 Reserved
Pos : 662 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E014 "res er viert" [SK 200E ... SK 5xxE] @ 2\mod_1347454273854_388.doc x @ 46776 @ @ 1
--- Reserved
E014
Pos : 663 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E015 [SK 180E ... SK 5xxE] @ 2\mod_1347454278051_388.doc x @ 46801 @ @ 1
--- Reserved
E015
Pos : 664 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E016 [SK 135E ... SK 5xxE, SK xxxE-FDS] @ 2\mod_1347454280625_388.doc x @ 46826 @ @ 1
16.0 Motor phase error
E016
16.1 Magnetisation current
monitoring
"Magnetisation current
monitoring"
Pos : 665 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E018 "res er viert" [SK 2xxE/SK 5xxE/SK 2xxE-FDS] @ 2\mod_1347454282777_388.doc x @ 46851 @ @ 1
18.0 Reserved
E018
Pos : 666 /Anleitungen/El ektr oni k/FU und Starter/6. M eldung en zum Betriebsz ustand/Stör meldung en (Auflistung)/F ehl er E019 [SK 180E/SK 2xxE/SK 5xxE/SK2xxE-FD S] @ 2\mod_1347454285788_388.doc x @ 46876 @ @ 1
19.0 Parameter identification
E019
"Parameter identification"
19.1 Star / Delta circuit incorrect
"Motor star / delta circuit
incorrect"
Pos : 667 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265495 @ @ 1
BU 0200 en-3118
6 Operating status messages
No signal from encoder
• Check 5V sensor if present.
• Check supply voltage of encoder.
The slip speed error limit was reached.
• Increase setting in P327.
The slip error monitoring has triggered; the motor could not
follow the setpoint.
• Check motor data P201-P209! (Important for the
current controller)
• Check motor circuit.
• In servo mode, check the encoder setting P300 and
check the following
• Increase setting value for torque limit in P112.
• Increase setting value for current limit in P536.
• Check deceleration time P103 and extend if
necessary
Error message for POSICON  see supplementary
instructions
Error message for POSICON  see supplementary
instructions
Error message for POSICON  see supplementary
instructions
A motor phase is not connected.
Check P539
•
Check motor connection
•
Required exciting current not achieved at moment of switch-
on.
Check P539
•
• Check motor connection
Error message for "Safe Pulse Block"  see supplementary
instructions
Automatic identification of the connected motor was
unsuccessful
• Check motor connection
• Check preset motor data (P201 ... P209)
• PMSM – CFC Closed Loop Operation: Rotor position
of motor incorrect in relation to incremental encoder
Perform determination of rotor position (initial enable
after a "Mains on" only with motor stationary (P330)
231