Nord Drivesystems NORDAC FLEX SK 200E Series User Manual page 201

Pos : 528 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P543 – Bus-Is twert 1- 3 [SK 1x0E, SK 2xxE, SK 2xxE-FDS] @ 2\mod_1346932171510_388.doc x @ 43296 @ @ 1
P543
[-01]
Actual bus value 1 ... 3
...
(Actual bus value 1 ... 3)
[-03]
0 ... 57 The return status value can be selected for bus actuation in this parameter.
{ [-01] = 1 } NOTE:
(P418).
{ [-02] = 4 }
For standardisation of the actual values: (please see chapter 8.9 "Standardisation of setpoint /
{ [-03] = 9 }
target values").
[-01] = Actual bus value 1
(Definition of frequencies (chapter 8.10))
Pos : 529 /Anleitungen/El ektr oni k/FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Parameter P543 – Bus-Is twert 1- 3_Einstellung en [SK 2xxE] @ 9\mod_1448353878755_388.doc x @ 266082 @ @ 1
10 = ... 11 reserved, Posicon
12 = BusIO Out Bits 0-7
13 = ... 16 reserved, Posicon
17 = Value analogue input 1,
18 = Value of analogue input 2,
* assignment of the digital inputs for P543 = 5
Bit 0 = DigIn 1 (FI)
Bit 4 = PTC input [FI]
Bit 8 = DigIn 5 (DI1, 1. SK...IOE)
Bit 12 = DigOut 1 (FI)
Pos : 530 /Allgemein/Allgemeingültig e Module/---------Seitenumbr uc h kompakt --------- @ 13\mod_1476369695906_0.doc x @ 2265495 @ @ 1
BU 0200 en-3118
For further details, please refer to the relevant bus manual or the description for
(Values from
0 = Off
1 = Actual frequency
2 = Actual speed
3 = Current
4 = Torque current (100% = P112)
5 = Digital IO* status
6 = ... 7 reserved, Posicon
8 = Setpoint frequency
9 = Error number
SK2x0E: Analogue input 1 (P400[-01]),
SK2x5E: AIN1 of the first I/O extension
- -
SK xU4 IOE (P400 [ 03]))
SK2x0E: Analogue input 2 (P400[-02]),
SK2x5E: AIN2 of first I/O extension
- -
SK xU4 IOE (P400 [ 04]))
Bit 1 = DigIn 2 (FI)
Bit 5 = reserved
Bit 9 = DigIn 6 (DI2, 1. SK...IOE)
Bit 13 = mech. Brake (FI)
0% ... 100% correspond
[-02] = Actual bus value 2
19 = Setpoint frequency master value (P503)
20 = Target frequency aft. mast. val. ramp,
"Setpoint frequency after master value
ramp"
21 = Actual freq. without slip Master value
"Actual frequency without master value
slip"
22 = Speed encoder,
"Speed from encoder"
BU0210
23 = Actual frequency with slip
V1.3)
"Actual frequency with slip"
BU0210 24 = Master value Actual freq. w. slip
above)
"Master value, actual freq. with slip"
BU0210 53 = Actual value 1 PLC
54 = Actual value 2 PLC
55 = Actual value 3 PLC
56 = Actual value 4 PLC
57 = Actual value 5 PLC
Bit 2 = DigIn 3 (FI)
Bit 6 = DigOut 3 (DO1, 1. SK...IOE)
Bit 10 = DigIn 7 (DI3, 1. SK...IOE)
Bit 14 = DigOut 2 (FI) (SK 2x0E)
5 Parameter
S P
to 0000 ... 4000
hex
[-03] = Actual bus value 3
(from software version
(SW 1.3 and
Bit 3 = DigIn 4 (FI)
Bit 7 = DigOut 4 (DO2, 1. SK...IOE)
Bit 11 = DigIn 8 (DI4, 1. SK...IOE)
Bit 15 = reserved
201
)
hex