Danfoss VLT DriveMotor FCP 106 Programming Manual page 43

Parameters
4.2.2 1-10 to 1-12 Motor Selection
NOTICE
This parameter group cannot be adjusted while the
motor runs.
The following parameters are active (x) depending on the
setting of parameter 1-10 Motor Construction.
Parameter 1-10 Motor Construction
Parameter 1-00 Configuration Mode
Parameter 1-03 Torque Characteristics
Parameter 1-06 Clockwise Direction
Parameter 1-14 Damping Gain
Parameter 1-15 Low Speed Filter Time
Const.
Parameter 1-16 High Speed Filter Time
Const.
Parameter 1-17 Voltage filter time const.
Parameter 1-20 Motor Power [kW]
Parameter 1-22 Motor Voltage
Parameter 1-23 Motor Frequency
Parameter 1-24 Motor Current
Parameter 1-25 Motor Nominal Speed
Parameter 1-26 Motor Cont. Rated Torque
Parameter 1-29 Automatic Motor
Adaption (AMA)
Parameter 1-30 Stator Resistance (Rs)
Parameter 1-33 Stator Leakage Reactance
(X1)
Parameter 1-35 Main Reactance (Xh)
Parameter 1-37 d-axis Inductance (Ld)
Parameter 1-39 Motor Poles
Parameter 1-40 Back EMF at 1000 RPM
Parameter 1-52 Min Speed Normal
Magnetising [Hz]
Parameter 1-60 Low Speed Load Compen-
sation
Parameter 1-61 High Speed Load
Compensation
Parameter 1-62 Slip Compensation
Parameter 1-63 Slip Compensation Time
Constant
Parameter 1-64 Resonance Dampening
Parameter 1-65 Resonance Dampening
Time Constant
Parameter 1-66 Min. Current at Low
Speed
Parameter 1-71 Start Delay
Parameter 1-72 Start Function
Parameter 1-73 Flying Start
MG03N202
Programming Guide
Parameter 1-80 Function at Stop
Parameter 1-82 Min Speed for Function at
Stop [Hz]
Parameter 1-90 Motor Thermal Protection
Parameter 2-00 DC Hold Current
Parameter 2-01 DC Brake Current
Parameter 2-02 DC Braking Time
Parameter 2-04 DC Brake Cut In Speed
[Hz]
Parameter 2-06 Parking Current
[0] [1] PM
Parameter 2-07 Parking Time
Asynchron Motor
Parameter 2-10 Brake Function
non-
Parameter 2-16 AC brake Max. Current
salient
Parameter 2-17 Over-voltage Control
x x
Parameter 4-10 Motor Speed Direction
x
Parameter 4-12 Motor Speed Low Limit
x x
[Hz]
x
Parameter 4-14 Motor Speed High Limit
x
[Hz]
Parameter 4-18 Current Limit
x
Parameter 4-19 Max Output Frequency
Parameter 4-58 Missing Motor Phase
x
Function
x
Parameter 14-40 VT Level
x
Parameter 14-41 AEO Minimum Magneti-
x x
sation
x x
Parameter 30-22 Locked Rotor Detection
x x
Parameter 30-23 Locked Rotor Detection
x
Time [s]
x x
Table 4.2 Parameters Activated by Setting of
x x
Parameter 1-10 Motor Construction
x
1-10 Motor Construction
x
Option:
x
[0]
x x
[1]
x
x
x
x
[2]
x
x
[3]
x
x
x
1-11 Motor Selection
Option:
x x
[0]
x x
x x
Danfoss A/S © 11/2015 All rights reserved.
Function:
Asynchron For asynchronous motors.
*
PM, non salient For permanent magnet (PM) motors with
SPM, non Sat surface-mounted (non-salient) magnets.
Refer to parameter 1-14 Damping Gain to
parameter 1-17 Voltage filter time const. for
details about optimizing the motor
operation.
PM, salient IPM, For permanent magnet (PM) motors with
non Sat interior (salient) magnets, without
inductance saturation control.
PM, salient IPM, For permanent magnet (PM) motors with
Sat interior (salient) magnets, with inductance
saturation control.
Function:
Default Motor Selection Automatically sets the manufac-
*
turer's settings for the selected
motor.
x x
x x
x x
x
x
x
x
4 4
x
x
x x
x
x x
x x
x x
x x
x x
x x
x x
x
x
x
x
41