Drive Information - Danfoss VLT AutomationDrive FC 360 Programming Manual

Parameter Lists
14-25 Trip Delay at Torque Limit
14-27 Action At Inverter Fault
14-28 Production Settings
14-29 Service Code
14-3* Current Limit Ctrl.
14-30 Current Lim Ctrl, Proportional Gain
14-31 Current Lim Ctrl, Integration Time
14-32 Current Lim Ctrl, Filter Time
14-4* Energy Optimising
14-40 VT Level
14-41 AEO Minimum Magnetisation
14-5* Environment
14-50 RFI Filter
14-51 DC-Link Voltage Compensation
14-52 Fan Control
14-55 Output Filter
14-6* Auto Derate
14-63 Min Switch Frequency
Dead Time Compensation Zero Current
14-64 Level
14-65 Speed Derate Dead Time Compensation
14-8* Options
14-89 Option Detection
14-9* Fault Settings
14-90 Fault Level

5.1.17 15-** Drive Information

Par. No. # Parameter description
15-0* Operating Data
15-00 Operating hours
15-01 Running Hours
15-02 kWh Counter
15-03 Power Up's
15-04 Over Temp's
15-05 Over Volt's
15-06 Reset kWh Counter
15-07 Reset Running Hours Counter
15-3* Alarm Log
15-30 Alarm Log: Error Code
15-31 InternalFaultReason
15-4* Drive Identification
15-40 FC Type
15-41 Power Section
15-42 Voltage
15-43 Software Version
15-44 Ordered TypeCode
15-45 Actual Typecode String
15-46 Drive Ordering No
15-48 LCP Id No
15-49 SW ID Control Card
15-50 SW ID Power Card
MG06C402
Programming Guide
60 s
[1] Warning
[0] No action
0 N/A
100 %
0.020 s
5 ms
66 %
66 %
[2] Grid type
[1] On
[5] Constant-on mode
[0] No Filter
[2] 2.0 kHz
[0] Disabled
ExpressionLimit
[0] Protect Option Config.
[3] Trip Lock
Default value
0 h
0 h
0 kWh
0 N/A
0 N/A
0 N/A
[0] Do not reset
[0] Do not reset
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
Danfoss A/S © Rev. 2014-03-31 All rights reserved.
All set-ups TRUE
All set-ups TRUE
1 set-up FALSE
1 set-up TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups FALSE
All set-ups FALSE
1 set-up FALSE
All set-ups FALSE
1 set-up TRUE
1 set-up FALSE
1 set-up FALSE
All set-ups FALSE
All set-ups FALSE
1 set-up TRUE
All set-ups TRUE
2-set-up Change Conver-
during sion index
operation
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up FALSE
1 set-up FALSE
1 set-up FALSE
1 set-up FALSE
1 set-up FALSE
All set-ups FALSE
1 set-up FALSE
1 set-up FALSE
1 set-up FALSE
1 set-up FALSE
0 Uint8
- Uint8
- Uint8
0 Uint32
0 Uint16
-3 Uint16
-4 Uint16
0 Uint8
0 Uint8
5
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
0 Uint16
- Uint8
- Uint8
Type
74 Uint32
74 Uint32
75 Uint32
0 Uint32
0 Uint16
0 Uint16
- Uint8
- Uint8
0 Uint8
0 Int16
0 VisStr[7]
0 VisStr[20]
0 VisStr[20]
0 VisStr[20]
0 VisStr[41]
0 VisStr[40]
0 VisStr[9]
0 VisStr[21]
0 VisStr[21]
0 VisStr[21]
125
5