Digital Outputs - Danfoss VLT AutomationDrive FC 360 Programming Manual

Parameter Descriptions
Available only if 1-00 Configuration Mode is set
to [6] Surface Winder or [7] Extended PID Speed
OL.
[74] PID enable When enabled, enables the extended process
PID controller. Equivalent to
parameter 7-50 Process PID Extended PID.
Available only if 1-00 Configuration Mode is set
to [7] Extended PID Speed OL.
Besides the selections above, default value and some extra
selections for specific terminals as below.
5-10 Terminal 18 Digital Input
Option: Function:
[8] Start Functions are described in parameter group 5-1*
*
Digital Inputs.
5-11 Terminal 19 Digital Input
Option: Function:
[10] Reversing Functions are described in parameter group
*
5-1* Digital Inputs.
5-12 Terminal 27 Digital Input
Option: Function:
[2] Coast inverse Functions are described in parameter group
*
5-1* Digital Inputs.
5-13 Terminal 29 Digital Input
Option: Function:
[14] Jog Functions are described in parameter
*
group 5-1* Digital Inputs.
[32] Pulse time based
5-14 Terminal 32 Digital Input
Option: Function:
[0] No operation Functions are described in parameter
*
group 5-1* Digital Inputs.
[82] Encoder input B
5-15 Terminal 33 Digital Input
Option: Function:
[0] No operation Functions are described in parameter
*
group 5-1* Digital Inputs.
[32] Pulse time based
[81] Enocder input A
5-16 Terminal 31 Digital Input
Option: Function:
[0] No operation Functions are described in parameter group
5-1* Digital Inputs.

4.6.3 5-3* Digital Outputs

The 2 solid-state digital outputs are common for terminals
27 and 29. Set the I/O function for terminal 27 in
5-01 Terminal 27 Mode, and set the I/O function for
terminal 29 in 5-02 Terminal 29 Mode.
MG06C402
Programming Guide
Terminals 42 and 45 can also be configured as digital
outputs.
NOTICE
These parameters cannot be adjusted while the motor is
running.
5-30 to 5-31 Digital Outputs
[0] No operation
[1] Control ready
[2] Drive ready
[3] Drive ready /
remote control
[4] Enable / no
warning
[5] Running
[6] Running / no
warning
[7] Run in range /
no warning
[8] Run on
reference / no
warning
[9] Alarm
[10] Alarm or
warning
[11] At torque limit The torque limit set in 4-16 Torque Limit
[12] Out of current
range
[13] Below current,
low
[14] Above current,
high
[15] Out of
frequency
range
[16] Below
frequency, low
[17] Above
frequency,
high
[18] Out of
feedback
range
Danfoss A/S © Rev. 2014-03-31 All rights reserved.
Default for all digital outputs and relay
outputs.
The control card is ready.
The frequency converter is ready for
operation and applies a supply signal on
the control board.
The frequency converter is ready for
operation and is in [Auto On] mode.
Ready for operation. No start or stop
command is been given (start/disable). No
warnings are active.
Motor is running and shaft torque present.
Output speed is higher than the speed set
in 1-81 Min Speed for Function at Stop
[RPM]. The motor is running and there are
no warnings.
Motor is running within the programmed
current and speed ranges set in
4-50 Warning Current Low to 4-51 Warning
Current High. There are no warnings.
Motor runs at reference speed. No
warnings.
An alarm activates the output. There are
no warnings.
An alarm or a warning activates the
output.
Motor Mode or 4-17 Torque Limit Generator
Mode has been exceeded.
The motor current is outside the range set
in 4-18 Current Limit.
Motor current is lower than set in
4-50 Warning Current Low.
Motor current is higher than set in
4-51 Warning Current High.
Output frequency is outside the frequency
range.
Output speed is lower than the setting in
parameter 4-40 Warning Freq. Low.
Output speed is higher than the setting in
parameter 4-41 Warning Freq. High.
Feedback is outside the range set in
4-56 Warning Feedback Low and
4-57 Warning Feedback High.
4 4
51