Parameters: 9-** Profidrive - Danfoss VLT AutomationDrive FC 360 Programming Manual

Parameter Descriptions

4.10 Parameters: 9-** PROFIdrive

9-00 Setpoint
Range:
0 [0 - 65535 ]
*
9-07 Actual Value
Range:
4 4
0 [0 - 65535 ]
*
9-15 PCD Write Configuration
Option:
[0]
[302] Minimum Reference
[303] Maximum Reference
[312] Catch up/slow Down Value
[341] Ramp 1 Ramp Up Time
[342] Ramp 1 Ramp Down Time
[351] Ramp 2 Ramp Up Time
[352] Ramp 2 Ramp Down Time
[380] Jog Ramp Time
[381] Quick Stop Ramp Time
[412] Motor Speed Low Limit [Hz]
[414] Motor Speed High Limit [Hz]
[416] Torque Limit Motor Mode
[417] Torque Limit Generator Mode
[553] Term. 29 High Ref./Feedb. Value
[558] Term. 33 High Ref./Feedb. Value
[590] Digital & Relay Bus Control
[593] Pulse Out 27 Bus Control
[595] Pulse Out 29 Bus Control
[615] Terminal 53 High Ref./Feedb. Value
[625] Terminal 54 High Ref./Feedb. Value
[696] Terminal 42 Output Bus Control
[748] PCD Feed Forward
[890] Bus Jog 1 Speed
[891] Bus Jog 2 Speed
[1680] Fieldbus CTW 1
[1682] Fieldbus REF 1
9-16 PCD Read Configuration
Option:
[0]
[1500] Operating hours
[1501] Running Hours
[1502] kWh Counter
[1600] Control Word
[1601] Reference [Unit]
[1602] Reference [%]
[1603] Status Word
[1605] Main Actual Value [%]
[1609] Custom Readout
[1610] Power [kW]
[1611] Power [hp]
[1612] Motor Voltage
74
Programming Guide
[1613]
Function:
[1614]
[1615]
[1616]
[1618]
Function:
[1622]
[1630]
[1633]
[1634]
Function:
[1635]
[1638]
[1639]
[1650]
[1652]
[1653]
[1657]
[1660]
[1661]
[1662]
[1663]
[1664]
[1665]
[1667]
[1668]
[1669]
[1670]
[1671]
[1672]
[1673]
[1679]
[1684]
[1685]
[1690]
[1691]
[1692]
[1693]
[1694]
[1695]
Function:
126
1037
Danfoss A/S © Rev. 2014-03-31 All rights reserved.
9-16 PCD Read Configuration
Option:
Frequency
Motor current
Frequency [%]
Torque [Nm]
Motor Thermal
Torque [%]
DC Link Voltage
Brake Energy /2 min
Heatsink Temp.
Inverter Thermal
SL Controller State
Control Card Temp.
External Reference
Feedback[Unit]
Digi Pot Reference
Feedback [RPM]
Digital Input
Terminal 53 Setting
Analog Input 53
Terminal 54 Setting
Analog Input AI54
Analog Output 42 [mA]
Pulse Input 29[Hz]
Pulse Input 33 [Hz]
Pulse Output 27 [Hz]
Pulse Output 29 [Hz]
Relay Output
Counter A
Counter B
Analog Output AO45
Comm. Option STW
FC Port CTW 1
Alarm Word
Alarm Word 2
Warning Word
Warning Word 2
Ext. Status Word
Ext. Status Word 2
9-18 Node Address
Range: Function:
[ 0 - Enter the station address in this parameter or
*
126 ] alternatively in the hardware switch. To adjust the
station address in parameter 9-18 Node Address,
set the hardware switch to 126 or 127 (i.e. all
switches set to 'on'). Otherwise this parameter
displays the actual setting of the switch.
9-19 Drive Unit System Number
Range:
[0 - 65535 ]
*
Function:
Function:
MG06C402