Profidrive - Danfoss VLT AutomationDrive FC 360 Programming Manual

Parameter Lists
8-3* FC Port Settings
8-30 Protocol
8-31 Address
8-32 Baud Rate
8-33 Parity / Stop Bits
8-35 Minimum Response Delay
8-36 Maximum Response Delay
8-37 Maximum Inter-char delay
8-4* FC MC protocol set
8-43 PCD Read Configuration
8-5* Digital/Bus
5 5
8-50 Coasting Select
8-51 Quick Stop Select
8-52 DC Brake Select
8-53 Start Select
8-54 Reversing Select
8-55 Set-up Select
8-56 Preset Reference Select
8-57 Profidrive OFF2 Select
8-58 Profidrive OFF3 Select
8-7* BACnet
8-79 Protocol Firmware version
8-8* FC Port Diagnostics
8-80 Bus Message Count
8-81 Bus Error Count
8-82 Slave Messages Rcvd
8-83 Slave Error Count
8-84 Slave Messages Sent
8-85 Slave Timeout Errors
8-88 Reset FC port Diagnostics
8-9* Bus Feedback
8-90 Bus Jog 1 Speed
8-91 Bus Jog 2 Speed

5.1.13 9-** PROFIdrive

Par. No. # Parameter description
9-00 Setpoint
9-07 Actual Value
9-15 PCD Write Configuration
9-16 PCD Read Configuration
9-18 Node Address
9-19 Drive Unit System Number
9-22 Telegram Selection
9-23 Parameters for Signals
9-27 Parameter Edit
9-28 Process Control
9-44 Fault Message Counter
9-45 Fault Code
9-47 Fault Number
9-52 Fault Situation Counter
9-53 Profibus Warning Word
122
Programming Guide
[0] FC
1 N/A
ExpressionLimit
ExpressionLimit
0.01 s
ExpressionLimit
0.025 s
ExpressionLimit
[3] Logic OR
[3] Logic OR
[3] Logic OR
[3] Logic OR
[3] Logic OR
[3] Logic OR
[3] Logic OR
[3] Logic OR
[3] Logic OR
ExpressionLimit
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
[0] Do not reset
100 RPM
200 RPM
Default value
0 N/A
0 N/A
ExpressionLimit
ExpressionLimit
126 N/A
1037 N/A
[100] None
0
[1] Enabled
[1] Enable cyclic master
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
Danfoss A/S © Rev. 2014-03-31 All rights reserved.
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
1 set-up FALSE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
All set-ups TRUE
All set-ups TRUE
4-set-up Change
during sion index
operation
All set-ups TRUE
All set-ups FALSE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
All set-ups TRUE
1 set-up TRUE
All set-ups TRUE
1 set-up FALSE
1 set-up FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
- Uint8
0 Uint8
- Uint8
- Uint8
-3 Uint16
-3 Uint16
-3 Uint16
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
-2 Uint16
0 Uint32
0 Uint32
0 Uint32
0 Uint32
0 Uint32
0 Uint32
- Uint8
67 Uint16
67 Uint16
Conver- Type
0 Uint16
0 Uint16
- Uint16
- Uint16
0 Uint8
0 Uint16
- Uint8
- Uint16
- Uint16
- Uint8
0 Uint16
0 Uint16
0 Uint16
0 Uint16
0 V2
MG06C402