Center Winder - Danfoss VLT AutomationDrive FC 360 Programming Manual

Parameter Descriptions

4.24.3 37-2* Center Winder

37-20 Winder Mode Selection
Option:
[0]
*
[1]
37-21 Tension Set Point
4 4
Range:
0 %
*
37-22 Taper Set Point
Range:
0 % [-110 - 110 %]
*
37-23 Partial Roll Diameter Value
Range:
5 %
*
37-24 Core1 Diameter
Range:
5 %
*
37-25 Core2 Diameter
Range:
5 %
*
37-26 Winder Jog Speed
Range:
0 %
*
37-27 TLD Low Limit
Range:
0 %
*
37-28 TLD High Limit
Range:
0 %
*
37-29 TLD Timer
Range:
0.001 s
*
37-30 TLDOnDelay
Option:
[0]
[1]
*
37-31 Diameter Limit Detector
Range:
100 %
*
37-32 Initial Diameter Measurement
Option:
[0] Set diameter when diameter reset
*
[1] Set diameter based on analog signal
110
Function:
Wind
Unwind
Function:
[0 - 100 %]
Function:
Function:
[5 - 100 %]
Function:
[5 - 100 %]
Function:
[5 - 100 %]
Function:
[0 - 100 %]
Function:
[0 - 100 %]
Function:
[0 - 100 %]
Function:
[0.001 - 5 s]
Function:
Disabled
Enabled
Function:
[0 - 100 %]
Danfoss A/S © Rev. 2014-03-31 All rights reserved.
Programming Guide
37-33 Diameter Measurement Input
Option:
[0]
*
[1]
[2]
37-34 Reading at Core
Range:
0
*
37-35 Reading at Full Roll
Range:
0 V
*
37-36 Tension Set Point Input
Option:
[0]
*
[1]
[2]
37-37 Taper Set Point Input
Option:
[0]
*
[1]
[2]
37-38 Tension Feedback Input
Option:
[0]
*
[1]
[2]
37-39 Tension Feedback Type
Option:
[0]
*
[1]
37-40 Center Winder Cmd Src
Option:
[0] Digital and parameter
[1] Parameter 3754~3759 control the functions
*
[2] Digital input control
37-41 Diameter Change Rate
Range:
0.001 %
37-42 Tapered Tension Change Rate
Range:
0.1 %
*
37-43 Diameter Calculator Min Speed
Range:
Function:
0 %
*
No Function
Input53(0~10 VDC or 0~20 mA )
Input54(0~10 VDC or 0~20 mA )
Function:
[0 - 10 ]
[0 - 20 V]
Par.3721
Input53(0~10 VDC or 0~20 mA )
Input54(0~10 VDC or 0~20 mA )
Par.3722
Input53(0~10 VDC or 0~20 mA )
Input54(0~10 VDC or 0~20 mA )
No Function
Input53(0~10 VDC or 0~20 mA )
Input54(0~10 VDC or 0~20 mA )
Load cell
Dancer
[0.001 - 0.05 %]
*
[0.1 - 1 %]
[0 - 100 %]
Function:
Function:
Function:
Function:
Function:
Function:
Function:
Function:
Function:
Function:
MG06C402