Saving Punch-In/Out Points During Rehearsal Or Recording - Sony PCM-3348HR Operation Manual

4-4-1 Saving Punch-In/Out Points During Rehearsal or Recording

Use the following procedure to save punch-in/out
points.
1
4
1
Set the channels for auto punch in/out to the
recording ready state.
2
Press and light the PLAY button to start playback.
3
At the point where you wish to start recording,
hold down the PLAY button, and press the REH
button.
The REH button lights, and the point at which the
button was pressed is stored in the IN-point
register.
At this point, the monitor output signal cross-fades
from the playback signal to the input signal.
S
SET UP MEMORY
REHEARSAL 2CH DIO RECALL
REC MUTE (REC DISABLE) SET UP ENABLE A B C D STORE
REC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
REC
READY
REPRO
INPUT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
REC
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
REC
READY
REPRO
INPUT
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
WORD MASTER
LENGTH SAMPLING FREQ SAFE REC MODE
REMOTE1,3,4 REMOTE2 24BIT 16BIT 44.056KHz 44.1KHz 48.0KHz ADVANCE ASSEMBLE INSERT
/LOCAL REC SYNC REC
SYSTEM
CONTROL
TAPE TIME
CTL
DF
TIME CODE
H MIN SEC
RELATIVE
LOCATE TIME
ABSOLUTE
POWER
TIMER
FRAME mSEC
H MIN SEC
VARI SPEED CONTROL STEREO SOUND MEMORY/DIGITAL COPY
DIGITAL COPY
Ø /ø
NORMAL %
SOURCE DESTINATION
SOUND MEMORY
VARI HALF CH CH
SPEED TONE
VARI
H.T./%
SPEED
– +
VARI MEM MEM MEM
SET PLAY STOP REC
Saving punch-in/out points during rehearsal or recording
Chapter 4 Basic Operations of the RM-3348HR Remote Control Unit
DIGITAL AUDIO REMOTE CONTROL UNIT RM-3348HR
MONITOR MODE CONTROL X'FADE TIME
ALL ALL ALL REPRO AUTO X'FADE
EXT
INDIVIDUAL REPRO INPUT MUTE MUTE INPUT OUTPUT
CONTROLLED
AUTO REC REC
17 18 19 20 21 22 23 24 TIME A1 A2
CODE
REC
READY
REPRO
INPUT
17 18 19 20 21 22 23 24 TIME A1 A2
CODE
ANALOG
MONITOR
REC
41 42 43 44 45 46 47 48
REC
READY
REPRO
INPUT
41 42 43 44 45 46 47 48
EXT CLOCK EMPHASIS
SYNC CLOCK ERROR MISMATCH SYSTEM
INT EXT DI REMOTES VIDEO WARNING ALARM
CUE
SLAVE TIMER MODE STORE RECALL
SF.mS 7 8 9
/F.S
REP SET CUE STORE
TC CHASE CTL/TC
–
CUE 4 5 6
PRE ROLL POST ROLL
SF + 1 2 3
IN OUT
= +/- 0
CLEAR
SCROLL
RTN RLB
CH
SYNC OFFSET
MODE
SET
– +
TRIM
AUTO
FWD/REV LOC
PUNCH
BEFORE AFTER
INVERT
º ‚ · π ®
REW FF PLAY STOP REC REH
START END
EDIT EDIT
4
At the recording end point, press any tape transport
operation button (PLAY, FF, REW or STOP).
The REH button goes off, and the point is saved in
the OUT point register.
At the same point the monitor output signal cross-
fades back from the input signal to the playback
signal.
In step 3, if you hold down the REC button and press
the PLAY button, recording begins, and the point at
which the REC button was pressed is stored in the IN
point register. Pressing any tape transport operation
button (PLAY, FF, REW or STOP) stops the
recording, and saves the end point in the OUT-point
register.
2
3
4-15