Sony PCM-3348HR Operation Manual page 33

4
With the TIMER MODE switch, select CTL
ABSOLUTE, and press the RESET button to set
the tape time display to "00
The tape timer display switches momentarily to
"00 00 00 ," then returns to its previous value.
H MIN SEC
5
(1) Set the switches as follows.
•
TIMER MODE switch: TIME CODE
•
TIME CODE selection switch: INT
•
TIME CODE GEN format selection switch:
Desired format
•
TC GEN switch on the MC board: REC RUN
(2) Holding down the SET button, press the
TIMECODE REC READY button to set the
time code channel to the recording ready state.
The TIME CODE REC READY button lights.
(3) Press and light the TIME CODE INPUT
button.
(4) Press the RESET button to reset the internal
time code generator to "00
Using an external time code
In place of step 5 of the procedure "Using the internal
time code generator," use the following procedure.
( 3 )
1 2 3 4 5 6
REC
REC
READY
OVER
–8
–16
–20
–24
–32
–42
–54
SET ALL CHANNEL
REC
MUTE
AUTO INPUT
00 00 ."
H MIN SEC
00 00 ."
H MIN SEC
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
REC
REC
READY
OVER
–8
–16
–20
–24
–32
–42
–54
TIME CODE A1 A2
RESET TAPE TIME
VARI
REC
RELATIVE SPEED
READY A CUE
STORE
ABSOLUTE
H MIN SEC
REPRO
TIMER LOCATE TIME
MODE
TIME CODE CUE
A RECALL
INPUT
A B
H MIN SEC
ANALOG
MONITOR
( 4 )
External time code operation
6
Holding down the REC button, press the PLAY
button.
The REC lamps for all channels light, and
recording starts.
The signal level for each channel is displayed on
the respective level meter.
7
When recording is finished, continue recording for
approximately 30 seconds, then press the STOP
button to stop recording.
For simultaneous play while recording
Press the ALL CHANNEL, TIME CODE, A1 or A2
REPRO buttons.
To set the CTL and time code start points to
desired values
In place of pressing the RESET button in step
enter a desired time value using the numeric buttons of
the RM-3348HR, then press the ↑ button.
The entered time value is sent to the tape time display
of the PCM-3348HR.
TIME
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 A1 A2 CTL FORMAT
CODE
MISMATCH
REC REC AFTER
REC
REC REC
READY READY
OVER OVER
0 0
–8 –8 0
EMPHASIS
–16 –16 –8
MISMATCH
–20 –20 –20
–24 –24
–32 –32
–42 –42
EXT CLOCK
–54 –54
ERROR
ERROR
SLOW WIND
B
ZERO º ‚ ·
LOCATE LOCATE REW FF PLAY
B
( 1 )( 2 )
REC WORD Fs EMPH INPUT SELECT SYNC CLOCK TIME CODE SYSTEM
SYSTEM
MODE LENGTH CONTROL
2CH-DIO READER GEN
ADVANCE 1,3,4
ALARM INSERT 24BIT 44.056kHz OFF ANALOG SDIF-2 ON INT X'tal 30/29(NDF) 30 INT LCL/REMOTE
REC
MASTER
SAFE ASSEM 16BIT 44.1kHz INDIVI DIGITAL MADI OFF EXT NORM 29(DF) 29(NDF) EXT REMOTE 2
-BLE
WARNING
48kHz ON INDIVI DI 25 29(DF) REGENE
MASTER ON (EXT)
SAFE
AUTO REMOTE 3 24 25
SYNC
SERVO VIDEO 24
REC
LOCK
OFF
SHUTTLE
π ® EDIT
STOP REC STOP
(Continued)
Chapter 3 Basic Operations
4 and 5,
3-7