Advance Recording; What Is Advance Recording; Basic Advance Recording - Sony PCM-3348HR Operation Manual

3-4 Advance Recording

3-4-1 What Is Advance Recording?

Regardless of any existing signals recorded on the
tape, the CTL signal, time code signal and digital
audio signals are recorded simultaneously.
This mode is used for live recording.
Simultaneous monitor output for the recorded signal
(simultaneous recording and playback) is possible.

3-4-2 Basic Advance Recording

Use the following procedure to carry out advance
recording.
3
1 2 3 4 5 6 7 8 9 10
REC
REC
READY
OVER
–8
–16
–20
–24
–32
–42
–54
SET ALL CHANNEL TIME CODE A1 A2
REC REC
MUTE READY
REPRO
AUTO INPUT
INPUT
ANALOG
MONITOR
5 5
REPRO
( 2 ) ( 3 )
buttons
Using the internal time code generator
1
Set the switches as follows.
•
MASTER SAFE switch: OFF
•
WORD LENGTH switch: Word length being used
•
Fs switch: Sampling frequency being used
•
EMPH switch: ON or OFF
2
Set the REC MODE switch on the system control
panel to ADVANCE REC.
3-6
Chapter 3 Basic Operations
5
4
( 4 )
11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
REC REC
REC REC
READY READY
OVER OVER
–8 –8
–16 –16
–20 –20
–24 –24
–32 –32
–42 –42
–54 –54
RESET TAPE TIME
VARI
RELATIVE
SPEED CUE
A B
STORE
ABSOLUTE
H MIN SEC
TIMER
LOCATE TIME
MODE
TIME CODE CUE
A B
RECALL
A B
H MIN SEC
5
( 1 )
Advance recording operation
Note
Normally, simultaneous recording and playback is
only possible during advance recording. However,
certain settings on the MC board can enable
simultaneous recording and playback for recording on
a prestriped tape.
For internal settings of the board, see "MC board" (page A-
20) in Appendixes, "Location of Parts and Controls."
7
36 37 38 39 40 41 42 43 44 45 46 47 48 TIME A1 A2 CTL
FORMAT
CODE SYSTEM
AFTER MISMATCH
REC
REC
REC
READY ADVANCE
ALARM
OVER REC
0 0
–8 0
EMPHASIS
–16 –8
MISMATCH
–20 –20 WARNING
MASTER
–24
SAFE
–32
–42
EXT CLOCK SERVO
–54
ERROR ERROR LOCK
SLOW WIND
º ‚ · π ®
ZERO
LOCATE LOCATE REW FF PLAY STOP REC
6
3
Holding down the SET button, press the ALL
CHANNEL REC READY button to set all digital
audio channels to the recording ready state.
If you wish to record on analog audio channels A1
and A2, holding down the SET button, press the
A1 A2 REC READY button to set channels A1
and A2 to the recording ready state.
The ALL CHANNEL REC READY button lights
(and the A1 A2 REC READY button lights).
MC board
2
REC WORD Fs EMPH INPUT SELECT SYNC CLOCK TIME CODE SYSTEM
MODE LENGTH 2CH-DIO READER GEN CONTROL
1,3,4
INSERT 24BIT 44.056kHz OFF ANALOG SDIF-2 ON INT X'tal 30/29(NDF) 30 INT LCL/REMOTE
MASTER
16BIT 44.1kHz INDIVI DIGITAL MADI OFF EXT NORM 29(DF) 29(NDF) EXT REMOTE 2
SAFE ASSEM
-BLE
48kHz ON INDIVI DI 25 29(DF) REGENE
ON
(EXT)
AUTO REMOTE 3 24 25
SYNC VIDEO 24
REC
OFF
SHUTTLE
EDIT
STOP
1 5
( 1 )
OFF ON
BACK UP 1
AUTO REC 2
MESSAGE 3
VARI SYNC 4
TEST
TIME CODE
TC GEN
REC FREE
RUN RUN
OUTPUT
NORM ADV
PB TC GAIN
NORM LOW
MC