Chapter 6 Digital Copy; Preparations - Sony PCM-3348HR Operation Manual

6-2 Preparations

6-2-1 Selecting the Digital Copy
Mode
Use the following procedure to select the digital copy
mode.
1
Set the REC MODE switch on the PCM-3348HR
system control block to INSERT.
2
Stop the tape transport.
3
Press and light the DIGITAL COPY button.
The LOCATE TIME display shows "dcoPY-1ch"
for about two seconds.
The REC READY, REPRO and INPUT buttons
for all channels go off, and all channels go into the
recording inhibited state.
TAPE TIME
CTL
TIME CODE
H
RELATIVE
LOCATE TIME
ABSOLUTE
TIMER
H
Lit
Operation mode (multi-channel mode)
STEREO SOUND MEMORY/DIGITAL COPY
DIGITAL COPY
SOURCE
SOUND MEMORY
CH
MEM MEM MEM
PLAY STOP
These points light. (multi-channel mode)
S
SET UP MEMORY
REHEARSAL 2CH DIO RECALL
REC MUTE (REC DISABLE) SET UP ENABLE A B C D
REC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
REC
READY
REPRO
INPUT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
REC
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
REC
READY
REPRO
INPUT
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
All buttons go off.
Making a digital copy during rehearsal or
recording
During rehearsal or recording, the DIGITAL COPY
button does not operate.
6-2

Chapter 6 Digital Copy

CUE
DF
MIN SEC
CUE
MIN SEC FRAME mSEC SF
SCROLL
CH
MODE
SET
DESTINATION
CH
FWD/REV
BEFORE AFTER
INVERT
START END
REC EDIT EDIT
DIGITAL AUDIO REMOTE CONTROL UNIT RM-3348HR
MONITOR MODE CONTROL X'FADE TIME
ALL ALL ALL REPRO AUTO X'FADE
EXT
STORE INDIVIDUAL REPRO INPUT MUTE MUTE INPUT OUTPUT
CONTROLLED
AUTO REC REC
17 18 19 20 21 22 23 24 TIME A1 A2
CODE
REC
READY
REPRO
INPUT
17 18 19 20 21 22 23 24 A1 A2
TIME
CODE
ANALOG
MONITOR
REC
41 42 43 44 45 46 47 48
REC
READY
REPRO
INPUT
41 42 43 44 45 46 47 48
Notes on the REC MUTE button
• If you press the DIGITAL COPY button while REC
MUTE button is lit, the REC MUTE button goes off,
and the unit exits from the REC MUTE state.
• While the DIGITAL COPY button is lit, the REC
MUTE button does not operate.
6-2-2 Selecting the Operation
Mode
Selecting the multi-channel mode
Press the 0, STORE, = and 3 buttons in that order.
The LOCATE TIME display shows "dcoPY-1ch" for
about two seconds. The trailing dots also light on the
destination channel display.
Selecting the two-channel mode
Press the 1, STORE, = and 3 buttons in that order.
The LOCATE TIME display shows "dcoPY-2ch" for
about two seconds. The trailing dots do not light on
the destination channel display.
Selecting the vocal-select mode
Press the 2, STORE, = and 3 buttons in that order.
The LOCATE TIME display shows "VocAL-SEL" for
about two seconds.
Checking the operation mode
Press the RECALL, = and 3 buttons in that order.
The LOCATE TIME display shows "dcoPY-1ch"
(multi-channel mode), "dcoPY-2ch" (two-channel
mode) or "VocAL-SEL" (vocal-select mode) for about
2 seconds.
Notes on changing the operation mode
• Changing the operation mode deletes the existing
channel settings, and the channel display shows "– –" .
• It is not possible to change the operation mode during
rehearsal or recording.