KEB COMBIVERT F4-F Applications Manual page 8

Introduction
4.4
5. Parameter ................................................................................................. 5.1.3
5.1
6. Functional Description ........................................................................... 6.1.3
6.1
6.2
6.3
Chapter Section Page
1 1 8
Drive-Mode .......................................................................................... 4.4.3
4.4.1 Adjustment Possibilities ....................................................... 4.4.3
4.4.2 Display and Keyboard ......................................................... 4.4.3
4.4.3 Setpoint Display /Setpoint Input .......................................... 4.4.3
4.4.4 Rotation Setting ................................................................... 4.4.4
4.4.5 Start / Stop / Run ................................................................ 4.4.4
4.4.6 Leaving the Drive-Mode ...................................................... 4.4.5
Parameter ............................................................................................ 5.1.3
5.1.1 Parameter Groups ............................................................... 5.1.3
5.1.2 Parameterlisting F4-F .......................................................... 5.1.5
Operating and Unit Datas .................................................................. 6.1.3
6.1.1 Summary of ru-Parameter ................................................... 6.1.3
6.1.2 Summary of In-Parameter ................................................... 6.1.3
6.1.3 Explanation to Parameter Description ................................. 6.1.4
6.1.4 Description of ru-Parameter ................................................ 6.1.5
6.1.5 Description of In-Parameter............................................... 6.1.16
Analog In- and Outputs ...................................................................... 6.2.3
6.2.1 Brief Description .................................................................. 6.2.3
6.2.2 Analog Inputs ...................................................................... 6.2.3
6.2.3 Interference Suppressor Filter Analog Inputs (An.1) ........... 6.2.6
6.2.4 Gain of Input Characteristic (An.3...5, An.9...11) ................. 6.2.6
6.2.5 Zero Point Hysteresis of Analog Inputs (An.2 / An.8) .......... 6.2.9
6.2.6 Analog Outputs ................................................................. 6.2.10
6.2.7 Gain of Output Characteristic (An.15/16, An.19/20) .......... 6.2.11
6.2.8 Used Parameters.............................................................. 6.2.14
Digital In- and Outputs ....................................................................... 6.3.3
6.3.1 Brief Description Digital Inputs ............................................ 6.3.3
6.3.2 Input Signals PNP / NPN (di.1) ........................................... 6.3.3
6.3.3 Terminal Status (ru.14) ........................................................ 6.3.4
6.3.4 Digital Inputs set by Software (di.15, di.16) ........................ 6.3.4
6.3.5 Digital Filter (di.0) ................................................................ 6.3.5
6.3.6 Inverting of Inputs (di.2)....................................................... 6.3.5
6.3.7 Strobe-Dependent Inputs (di.17...di.19) .............................. 6.3.6
6.3.8 Function Assignment (di.3...di.12) ....................................... 6.3.7
6.3.9 Input Status (ru.16) ............................................................. 6.3.8
6.3.10 Brief Description - Digital Outputs ....................................... 6.3.9
6.3.11 Output Signals ................................................................... 6.3.10
6.3.12 Switching Conditions (do.1...do.8) ..................................... 6.3.10
6.3.13 Output Filter Unit (do.26...do.31) ....................................... 6.3.12
6.3.14 Inverting of Switching Conditions do.17...do.24 ............... 6.3.14
6.3.15 Selection of Switching Conditions (do.9...do.16) .............. 6.3.14
6.3.16 Logic Operation of Switching Conditions (do.25) .............. 6.3.14
6.3.17 Inverting of Outputs (do.0) ................................................. 6.3.15
Date Name: Basis
21.06.99 KEB COMBIVERT F4-F
General
© KEB Antriebstechnik, 1999
All Rights reserved