Omron 3G3MV-PDRT2 User Manual page 357

Appendices
Con- Regis- Class 64 (hex)
stant ter num-
In-
ber
stance
(hex)
F6-01 0395 ---
F7-01 0396 ---
F8-01 0398 ---
F9-01 0399 ---
F9-02 039A ---
F9-03 039B ---
F9-04 039C ---
F9-05 039E ---
F9-06 039F ---
Note 1. When the control mode is changed, the Inverter will revert to default settings. (The open loop
vector control default settings are given above.)
Note 2. Within the setting range (1 to 38), 4, 10, 11, 12, 13, 14, 25, 28, 34, and 35 cannot be set,
and 29 to 31 are not used.
■ External Terminal Function Parameters
Con- Regis- Class 64 (hex)
stant ter num-
In-
ber
stance
(hex)
H1-01 0400 01
H1-02 0401 01
H1-03 0402 01
H1-04 0403 01
H1-05 0404 01
H1-06 0405 01
H2-01 0406 01
H2-02 0407 01
H2-03 0408 01
H3-01 0409 01
H3-02 040A 01
H3-03 040B 01
H3-04 040C 01
H3-05 040D 01
Name
At-
tribute
--- Not used.
--- Output pulse multiple selection
--- Operation selection (E-15)
--- Communications external fault input
selection
--- Communications external fault input
detection selection
--- Communications external fault input
operation selection
--- Not used.
--- Torque reference/Torque limit selection
from communications
--- DeviceNet operation selection
Name
At-
tribute
7E Multi-function input 1: terminal 3 selec-
tion
7F Multi-function input 2: terminal 4 selec-
tion
80 Multi-function input 3: terminal 5 selec-
tion
81 Multi-function input 4: terminal 6 selec-
tion
82 Multi-function input 5: terminal 7 selec-
tion
83 Multi-function input 6: terminal 8 selec-
tion
84 Multi-function contact output: terminal
9 to 10.
85 Multi-function output 1: terminal 25.
86 Multi-function output 2: terminal 26.
87 Signal selection: terminal 13 (Voltage)
88 Frequency reference (voltage)
gain: terminal 13
89 Frequency reference (voltage)
bias: terminal 13
8A Multi-function analog input signal
selection: terminal 16
8B Multi-function analog input signal
selection: terminal 16
Chapter 10
Setting Setting Default
range unit setting
--- --- 0
0 to 4 1 1
0 to 3 1 1
0, 1 1 0
0, 1 1 0
0 to 3 1 1
--- --- 0
0, 1 1 1
0 to 3 1 1
Setting Setting Default
range unit setting
0 to 77 1 24
14
3 (0)
(See
note 1.)
4 (3)
(See
note 1.)
6 (4)
(See
note 1.)
8 (6)
(See
note 1.)
0 to 37 1 0
1
2
0, 1 1 0
0.0 to 0.1% 100.0
1000.0
−100.0 to
0.1% 0.0
100.0
0, 1 1 0
0 to 1F 1 1F
Write
during
opera-
tion
---
No
No
No
No
No
---
No
No
Write
during
opera-
tion
No
No
No
No
No
No
No
No
No
No
Yes
Yes
No
No
10-99