Special Adjustment Parameters; Operator Parameters - Omron 3G3MV-PDRT2 User Manual

Appendices
Con- Regis- Class 64 (hex)
stant ter num-
In-
ber
stance
(hex)
L8-10 04B6 04
L8-11 04B7 04
L8-12 04B8 04
L8-15 04BB 04
L8-18 04BE 04
Note 1. Values in parentheses are for 400-V-class Inverters.
Note 2. If the setting is 0, the axis will accelerate to the specified speed over the specified acceler-
ation time (C1-01 to C1-08).
Note 3. The initial value when C6-01 is set to 1 is given. If C6-01 is set to 0, the initial value will be
150%.
Note 4. Values in parentheses are for Asian model Inverters.

Special Adjustment Parameters

■
Con- Regis- Class 64 (hex)
stant ter num-
In-
ber
stance
(hex)
N1-01 0580 05
N1-02 0581 05
N2-01 0584 05
N2-02 0585 05
N2-03 0586 05
N3-01 0588 05
N3-02 0589 05
N3-03 058A 05
N3-04 058B 05

Operator Parameters

■
Con- Regis- Class 64 (hex)
stant ter num-
In-
ber
stance
(hex)
o1-01 0500 05
o1-02 0501 05
o1-03 0502 05
o1-05 0504 05
o2-01 0505 05
o2-02 0506 05
Name
At-
tribute
B6 Cooling fan control selection
B7 Cooling fan control delay time
B8 Ambient temperature
BB OL2 characteristics selection at low
speeds
BE Soft CLA selection
Name
At-
tribute
80 Hunting-prevention function selection
81 Hunting-prevention gain
84 Speed feedback detection control
(AFR) gain
85 Speed feedback detection control
(AFR) time constant
86 Speed feedback detection control
(AFR) time constant 2
88 High-slip braking deceleration fre-
quency width
89 High-slip braking current limit
8A High-slip braking stop dwell time
8B High-slip braking OL time
Name
At-
tribute
00 Monitor selection
01 Monitor selection after power up
02 Frequency units of reference setting
and monitor
04 LCD brightness
05 LOCAL/REMOTE key enable/disable
06 STOP key during control circuit termi-
nal operation
Chapter 10
Setting Setting Default
range unit setting
0, 1 1 0
0 to 300 1 s 60
45 to 60 1°C 45
0, 1 1 1
0, 1 1 1
Setting Setting Default
range unit setting
0, 1 1 1
0.00 to 0.01 1.00
2.50
0.00 to 0.01 1.00
10.00
0 to 2000 1 ms 50
0 to 2000 1 ms 750
1 to 20 1% 5
100 to 1% 150
200
0.1 to 0.1 s 1.0
10.0
30 to 1 s 40
1200
Setting Setting Default
range unit setting
4 to 33 1 6
1 to 4 1 1
0 to 1 0
39999
0 to 5 1 3
0, 1 1 1
0, 1 1 1
Write
during
opera-
tion
No
No
No
No
No
Write
during
opera-
tion
No
No
No
No
No
No
No
No
No
Write
during
opera-
tion
Yes
Yes
No
Yes
No
No
10-63