Show Fiber-Ports Optical-Transceiver-Info - Ubiquiti EDGESWITCH ES-24-250W Command Reference Manual

EdgeSwitch CLI Command Reference
Term
Output Power
Input Power
TX Fault
LOS
Example: The following information shows an example of the command output:
(UBNT EdgeSwitch) #show fiber-ports optical-transceiver all
Port Temp Voltage
[C] [Volt]
-------- ---- -------
0/49 39.3 3.256
0/50 33.9 3.260
0/51 32.2 3.256

show fiber-ports optical-transceiver-info

This command displays the SFP vendor-related information such as the vendor name, SFP serial number, and SFP
part number . The values are derived from the SFP's A0 table using the I
show fiber-ports optical-transceiver-info {all | slot/port}
Format
Mode
Privileged EXEC
Term
Port
Vendor Name
Link Length (50um, OM2)
Link Length (62.5um, OM1)
Serial Number
Part Number
Nominal Bit Rate (Mbps)
Rev
Ubiquiti Networks, Inc.
Description
Measured optical output power relative to 1mW.
Measured optical power received relative to 1mW.
Transmitter fault.
Loss of signal.
Output
Current Power
[mA] [dBm]
------- ------- -------
5.0 -2.234 -2.465
5.3 -2.374 -40.000
5.6 -2.300 -2.897
Description
The interface (slot/port).
The vendor name is a 16-character field that contains ASCII characters, left-aligned and padded on
the right with ASCII spaces (20h). The vendor name is the full name of the corporation, a commonly
accepted abbreviation of the name of the corporation, the SCSI company code for the corporation, or
the stock exchange code for the corporation.
This value specifies link length that is supported by the transceiver while operating in compliance with
applicable standards using 50 micron multimode OM2 [500MHz*km at 850nm] fiber. A value of zero
means that the transceiver does not support 50 micron multimode fiber or that the length information
must be determined from the transceiver technology.
This value specifies link length that is supported by the transceiver while operating in compliance
with applicable standards using 62.5 micron multimode OM1 [200 MHz*km at 850nm, 500 MHz*km
at 1310nm] fiber. A value of zero means that the transceiver does not support 62.5 micron multimode
fiber or that the length information must determined from the transceiver technology
The vendor serial number (vendor SN) is a 16 character field that contains ASCII characters, left-
aligned and padded on the right with ASCII spaces (20h), defining the vendor's serial number for the
transceiver. A value of all zero in the 16-byte field indicates that the vendor SN is unspecified.
The vendor part number (vendor PN) is a 16-byte field that contains ASCII characters, left aligned and
added on the right with ASCII spaces (20h), defining the vendor part number or product name. A value
of all zero in the 16-byte field indicates that the vendor PN is unspecified.
The nominal bit (signaling) rate (BR, nominal) is specified in units of 100 MBd, rounded off to the
nearest 100 MBd. The bit rate includes those bits necessary to encode and delimit the signal as well as
those bits carrying data information. A value of 0 indicates that the bit rate is not specified and must
be determined from the transceiver technology. The actual information transfer rate will depend on
the encoding of the data, as defined by the encoding value.
The vendor revision number (vendor rev) contains ASCII characters, left aligned and padded on the
right with ASCII spaces (20h), defining the vendor's product revision number. A value of all zero in this
field indicates that the vendor revision is unspecified.
Input
Power TX LOS
[dBm] Fault
----- ---
No No
No Yes
No No
C interface .
2
Utility Commands
115