Subject to alterations without prior notice, errors and omissions excepted. E & OE. We wish you a lot of fun and success while exercising and working with your h/p/cosmos running machine. Franz Harrer President h/p/cosmos sports &...
[3.H1] Professional application in sports and fitness ....................17 [3.H2] Professional application in the medical field ...................... 17 [3.H3] h/p/cosmos medical running machines - MDD medical device directive. Safety standards ......18 [3.I] Forbidden use ................................21 [4.] Installation & commissioning ............................22 [4.A] Transport, unpacking and packaging ..........................
Page 8
[10.E1] Safety precautions and operation ........................141 [10.E2] Operation and adjustment ..........................142 [10.F] Special handrails ................................143 [10.G] h/p/cosmos airwalk se 135 (available as of 10/2008) ....................144 [10.H] Unweighting system h/p/cosmos airwalk ........................145 [10.H1] Vests for subjects for h/p/cosmos airwalk ......................145 [10.I] Wheelchair ramp ................................
Page 9
[12.] Disposal ..................................164 [12.A] Disassemble and cut up ............................... 164 [12.B] h/p/cosmos running machine ............................164 [12.C] h/p/cosmos service oil / grease ............................ 164 [12.D] h/p/cosmos running belt ............................... 164 [13.] Contact ..................................165 [13.A] Service department ..............................165 [13.B] Sales department .................................
This instruction manual is part of the device and must always be accessible for every user. Exact observance of the instruction manual is a requirement for the appropriate operation of an h/p/cosmos device. Holding the handrails during exercise may effect the exercise results (e.g. heart rate, ECG, oxygen uptake, etc.). Under normal conditions and for healthy subjects we recommend to hold the handrails only for emergency or when needed for safety or unweighting.
Patient security according to VDE 0750 (IEC 601-1) type B [3.D2] If your h/p/cosmos device has a c mark with a 4-digit number (e.g. n) at the identification plate, it is a medical product. At your h/p/cosmos medical product the patient is protected/isolated from the mains in accordance with the safety standard referring to the requirements for leakage current values according to IEC 601- 1 type B.
[3.D4] If units installed outside medically utilized locations (e. g. external printer, host computer etc.) are connected to an h/p/cosmos unit installed in a medically utilized location the VDE 0750 regulations must be observed. Connection only via … 1. Optical fibre or optocoupler (4 kV checked and approved) or …...
(e.g. swimming pool, sauna, etc.) nor in environmental chambers. If not stated otherwise in the delivery information h/p/cosmos devices are designed for operation in normal climatic surroundings (DIN IEC 601-1): + 10 °...
Safety standards, norms [3.G] All h/p/cosmos running-machines are produced according to strict safety- and quality controls. The running machine must not be used, if the certificates/permissions and the (according to the list of technical specifications) defined safety standards do not correspond with the local and country-specific requirements. The country-specific requirements must be compared before initial operation.
As a manufacturer it is h/p/cosmos’ duty, and as the distributor or end- user/operator of the running machine it is your duty, to minimize those dangers as far as possible.
Page 19
To reduce the risk for users, h/p/cosmos running machines have a gap of less than 4 mm and it is marked clearly with additional danger precaution stickers.
Page 20
Despite that some of the above mentioned laws and guidelines are only binding within the European Union, the patient’s needs, the risks and the required safety procedures are the same all over the world. We ask all parties involved to help in improving safety. Some examples for safety features at h/p/cosmos devices: Potential isolation Opto coupler board...
A safety arch with chest belt and fall-stop is also obligatory in this case. In environmental conditions, others than specified in the chapter „technical specifications“ and “environmental conditions“, h/p/cosmos devices must not be used (e.g. in wet and humid areas, swimming pools, sauna, environmental chambers, high-pressure-, low-pressure, altitude- and oxygen-chambers, etc.).
Within Germany mostly all devices are delivered and assembled by h/p/cosmos directly or by an authorised forwarder. If delivered by h/p/cosmos the packaging will be taken back and recycled.
The levelling sockets and the front wheels of the elevation system may cause a print in the flooring. In case of sensitive flooring please use h/p/cosmos floor mats for protection: Floor protection mat 150/50 for running machines with deck size 150x50 cm [cos14005]...
Page 25
(~ 500 kg) / m². At h/p/cosmos gaitway with integrated force plate the transportation locks have to be removed after erection. Drive elevation up to max of 25 %. Loosen the four M8 screws, indicated with the red arrows at the underside of the alu- force plates and remove them.
To start again you have to switch-on the running machine at the main „ON“ switch and than press START at the keyboard. Installation of any electrical device and h/p/cosmos running-machines must only be carried out at a voltage power connection with ground wire (earthing) including leakage-current protection-switch (interrupter) and according to VDE 0100 or/and the currently valid regulations and directives.
One copy of this protocol [cos11690xx] remains at the owner’s manual and the original of the protocol with the „first measured values“ shall be sent to the manufacturer h/p/cosmos. Picture: Example for electric safety testing device based on IEC 601-1 Potential equalization [4.C3]...
The authorized technician (distributor or service partner) has to check whether the installation of the device has been performed properly, before the customer is introduced into the operation of the h/p/cosmos device. For detailed information and instructions for installation and commissioning please refer to all respective individual chapters in this manual.
Page 37
For details please refer to chapter „maintenance / inspections“. One copy of this protocol [cos11690xx] remains at the owner’s manual and the original with the „first measured values“ shall be sent to h/p/cosmos. The potential equalization cable has to be ...
To control via USB interface the processor must be a Pentium 1.8 GHz or higher. To use all the functions described below and for maintenance and service we recommend the PC software h/p/cosmos para control ®...
7 different acceleration levels and deceleration levels are available for all modes and for remote control via interface and h/p/cosmos coscom protocol. Max. acceleration level and minimum acceleration level see chapter: User options / optional functions. The following diagram shows the acceleration levels at a running machine with maximum speed of 40km/h.
Test No 21 ... 28 are user defined (free programmable Profiles). For a better and easier documentation we recommend to use the serial printer interface or to connect an external PC in order to use the h/p/cosmos para graphics ®...
80% of their max. heart rate ( 220 – age). The test duration and heart rate are measured immediately after finishing the 2 km distance. At h/p/cosmos devices the heart rate is measured every 500m due to higher accuracy.
Page 68
A serial printer or a PCL-printer with parallel/centronics plug und converter [cos10056] can be connected directly to the h/p/cosmos running machine. Following data can be printed after the UKK walk test even without using any PC: UKK fitness index, date, time, test duriation, distance, elevation, heart rate, age, sex, body-mass-index (BMI).
For a better documentation we recommend to use a test result (Fitness index and printer linked to the serial interface RS232 or/and to use time) an external PC with the Software h/p/cosmos para ® graphics Programming-example: free definable profile [5.B17] Programming and correction of a free programmed test is possible in test mode „...
Optional settings serve for example as an acknowledgement of error notes on the display, or for the standard setting of the device: selection of RS232 interface protocol, etc. Remark for devices without UserTerminal: For optional settings on devices without UserTerminal an external UserTerminal or a connected PC with the software h/p/cosmos para control ® is required.
List of user options / optional functions [6.A2] For devices without UserTerminal: An external UserTerminal or PC software h/p/cosmos para control ® is required to control the running machine via RS232 interface. Option Description Comment / Display [6.A2]...
Page 79
Various Ergospirometry OFF = RS232 not active / no protocol / interface deactivated systems support the h/p/cosmos coscom 1 = h/p/cosmos coscom v1, v2, v3 with Baudrate 9600 bps protocol. Individual adaptation ( standard setting COM 1 and COM 2) protocol request.
Page 80
NOT valid for control and operation via RS232-interface. In this case the acceleration and deceleration level is set in option no. 29 resp. set in the corresponding command of the h/p/cosmos coscom protocol. § OP28 Maximum acceleration and deceleration blinking, reports the max.
Administrator options [6.B] The administrator options are only accessible by h/p/cosmos staff and authorised service engineers. The access is only possible with a special code which is not depicted here. Changing an administrator option might cause serious problems if you are not familiar with all the details. Therefore the h/p/cosmos service has to be contacted before doing any changes in the administrator options.
Page 84
According to the selected device type (in OPTION 03) the standard maximum speed will be indicated in the SPEED Display. Example: h/p/cosmos mercury 4.0 = 22.0 km/h; h-p-cosmos discovery 4.0 = 40 m/min For safety purposes (e.g. for beginners) the max. speed of every treadmill model can be limited.
Page 86
To activate the motor break it is necessary to additionally change some parameters at the frequency inverter. Ask the service department of h/p/cosmos sports & medical gmbh for detailed instruction. Attention! If the device is switched off or disconnected from...
Page 87
If the speed measurement is switched off in OP11, then OP34 will only report internal program absolutes. In the other case following values are stored: Running machine series h/p/cosmos mercury with special speed 10 km/h: Speed Calibration Value: 8.490 Inverter Frequency: 80.2 Hz...
Page 88
[6.B1] special speed 45 km/h: Speed Calibration Value: 2.874 Inverter Frequency: 125 Hz Running machine series h/p/cosmos pulsar 3p with 40 km/h: Speed Calibration Value: 2.874 Inverter Frequency: 110 Hz Running machine series h/p/cosmos pulsar 3p with special speed 45 km/h: Speed Calibration Value: 2.874...
Page 89
Appropriate protocols and inspection instructions are available at h/p/cosmos service. To provide for this an error message "E 02" "HELP" for the TSC-service interval will appear in the display after expiration of a time period of 12 month.
Page 91
10 volt. Note down the voltage at the service report! (not possible with digital control via RS485) Read off the speed and write down the value at the h/p/cosmos service report: OP 48: _____ km/h Stop the running belt with the STOP key.
Page 93
( models h/p/cosmos venus since 1997) 4 = elevation control: linear motor for 0 - 24% elevation, increment sensor, lift range 240 mm (h/p/cosmos mercury models since 1997) 5 = elevation control: linear motor for 0 - 28% elevation, increment sensor, lift range 300 mm (h/p/cosmos quasar 4.0...
Preventive maintenance [7.A] The h/p/cosmos authorised service engineers are happy to help you in the case of occurring problems. A preventive maintenance can avoid problems in the future and is indispensable for the safety of such technical devices. Therefore ask for an annual preventive maintenance contract, which is highly recommended by the manufacturer, from our service department.
The main inspection sticker on the device (e.g. running machine) certifies also the inspection of the optional equipment and the accessories. However, inspection intervals for optional equipment and accessories (e.g. rope of h/p/cosmos airwalk unweighting system, chest belt for safety harness, compressors, etc.) can deviate significantly from inspection intervals of the main device.
An h/p/cosmos authorized technical service engineer will then advise what corrective action needs to be taken. Only use original h/p/cosmos special oil. The use of other oils or the ignoring of the regular lubrication checks can lead to damage of the running belt, running deck or the lubrication system and a reduction of warranty liability.
The tissue needs to be pulled through the gap between running belt and running surface in a defined lenght in order to absorb a certain quantity of lubricant. Based on previous experience h/p/cosmos is able to evaluate the quantity of the oil film by measuring the weight difference. However, it needs to be considered that this test can only find out approximate values and trends and can never replace the direct survey by the authorized h/p/cosmos technician in the prescribet time intervals.
Please contact h/p/cosmos to receive the special oil. The running belt should be lubricated after 1000 km (special devices might have different intervals) at the latest or/and after hearing dry grinding noises during operation. After lubrication the oil message has to be terminated with "OPTION 01".
Thus at those models a lubrication test (tissue-test) according the instruction (available from h/p/cosmos) must be performed in the course of the obligatory yearly maintenance. The test must be sent back to h/p/cosmos afterwards for evaluation purposes.
Special oil for sliding plate with automatic lubrication/0.25l-bottle [cos14007] Special oil for sliding plate with automatic lubrication/0.50l-bottle [cos13438] Set back of oil message MCU 4 without UserTerminal [7.D5] An external UserTerminal or the PC-software h/p/cosmos para control ® is required for this. Further instructions see "Devices with UserTerminal”.
At devices with external control unit the internal space of the control unit must be cleaned as well. The cleaning of the surfaces of the treadmill can be done with a light moistened cloth. For disinfection h/p/cosmos recommends Bacillol plus [cos12179].
Page 125
At MCU5 control electronic (as of manufacturing date 12/2007) this error exclusively shows a defect of the option memory (FRAM). In this case, please contact h/p/cosmos and request a service technician. Optional setup restores to default factory setting and device...
"5 times LONG (code for "0")" and 1 time SHORT + 4 times LONG (code for "1") will be repeated 3 times. Error Code list see: Devices with UserTerminal. The error messages have to be terminated with "OPTION 01". An external UserTerminal or a PC software h/p/cosmos para control ®...
Running machines [9.A] UserTerminal 6 LCD displays / 6 keys / display of mode and unit with LED. „lt-models“ and „h/p/cosmos 150/50 locomotion E med“ (Display & Keyboard) have no UserTerminal (no display, no keyboard). Control only via interface. Power supply...
Page 131
(TO = 15 %) converts to approx. 5 full elevation cycles. Overload can result in temporary tripping of the fuse, but can be used again after short cool down period. Treadmills of the h/p/cosmos saturn series built approx. before January 2007 have a maximum elevation of 25%.
IEC 601-1: 6.8.2.c, 19.2.b, 19.2.c). More recent computers will have only an USB interface instead of the RS232 interface. For that case an „USB to RS232 interface-adapter-cable“ is available at h/p/cosmos under item no. cos12769. To control via USB interface you need a processor Pentium 1.8 GHz or higher.
The h/p/cosmos arm supports (patent no.: DE 199 16 508 A1) are available for the h/p/cosmos running machines with running deck size 150/50, 170/65 and 190/65 cm but not for running machines with adjustbale handrails.
6 keys incl. 2m spiral cord cos10106 mount for additional keyboard on arm support cos10111 h/p/cosmos additional stop button (red button on top of handgrip) for arm support right cos10107 h/p/cosmos additional stop button (red button on top of handgrip) for arm support left cos10108 mount for additional stop button on handrail with clamp for circular tube 60mm ...
While adjusting make sure that you do not pen in yourself or any other person at the danger spots (squeezing and jamming spots). Using the h/p/cosmos arm support with the adjustable handrails is not possible. Reproducibility of adjustments [10.C2]...
Handrails adjustable. Parallel bars with gas struts and locking lever [10.D] The bar handrails adjustable in height and width are available for the h/p/cosmos running machine of the “locomotion series” exclusively. The individually adjustable handrails offer utmost safety at best possible freedom of movement. Well suited for therapy with insecure and elderly patients as well as for therapy with children.
If turing the UserTerminal to outside position, then at least 1 emergency-stop-button has to remain in reach of the subject at any time. The use of the h/p/cosmos arm supports is not possible with the adjustable bar handrails. Adjustment of the bar handrails [10.D2]...
2 pillars handrail detachable / separable Details and order numbers are available at the manufacturer h/p/cosmos or at your local authorized distributor. The crossbar always needs to be positioned in that way that at least 2/3 of the running surface behind the crossbar is free for the user.
135 (available as of 10/2008) [10.G] The „h/p/cosmos airwalk se 135“ is a user friendly and novel dynamic unweighting system with central point suspension for manual locomotion therapy. It improves the manual training due to constant un-weighting of the patient in the vertical movement area.
It is possible to use the h/p/cosmos airwalk with the running machine series with track size 150/50cm or 170/65cm or 190/65cm, and as well with most running machines produced by other manufacturers.
[10.J] With the help of the h/p/cosmos wheel chair stabilizer it is easy to keep wheel chairs with 4 or 3 wheels safely in lane. The guide rail is fixed between the two pillars of the right-hand side handrail.
The ceiling height should be at least 2.46m / 97.6 inches (0 % elevation) rsp. 2.57 / 101.6 inches (24 %) if used with h/p/cosmos mercury and 2.51 / 96.5 inches (0 %) rsp. 2.68 m / 105.5 inches (max. elevation) if used with running machines h/p/cosmos quasar or h/p/cosmos pulsar.
Bottle holder [10.M] The bottle holder is available for all h/p/cosmos running machines and can be easily fixed with a clamp on the handrail. The position of the bottle holder must not be at the rear end of the handrail due to this end must be reachable for the subject.
RS232 of the running machine. Attention: For a printer with a parallel interface you will need a commercial interface- converter, available in every computer-store, at your local dealer or from the manufacturer (h/p/cosmos order no. [cos10056]). If Option 20: 3 is chosen (printer protocol see list of options), following data will be printed out: Interface converter for printer [cos10056] file: n:\article\cos14310m5-v1.04hpc-en\20080901_cos14310m5-v1.04hpc-en_manual_h-p-cosmos_running_machine.doc...
3.0. In addition to the pure remote control function of h/p/cosmos treadmill-ergometers over the pc the software has integrated now a lot of additional functions such as an option setting configuration tool with integrated storage function, firmware update over flash eprom, quick-stop-key, cool-down-key, pause-key, target speed settings, target elevation settings, stop-count-down, display reset, etc.
Page 155
& info DVD [cos10067] which is delivered together with every h/p/cosmos treadmill-ergometer. Alternatively the software can be downloaded at www.h-p-cosmos.com/en/software. At aforementioned link also a manual can be found in which all functions of the new para control 4.0 are described in detail.
The data can be converted by the software and be taken over and evaluated e.g. by EXCEL, or h/p/cosmos para analysis software. A take over and processing of the data within a spreadsheet (EXCEL, etc.) or an editor is also possible with the help of the h/p/cosmos para graphics ®...
The evaluation of heart rate and lactate curves after graded test is possible on the basis of individual selected threshold models in graphics and tables. It is possible to enter the test data in h/h/p/cosmos para analysis ®...
& options PC Software h/p/cosmos para motion [10.W] The h/p/cosmos para motion is a software for recording and evaluation of video analysis with individual report for printout, incl. control functions of h/p/cosmos running machines. Basic functions and features Digital, software-based video recordings with treadmill control for all h/p/cosmos treadmills parallel to recording with feedback.
This certificate of compliance covers all running machine models which are listed above and which are produced by h/p/cosmos on and from November 24, 2006. The validity of this certificate of compliance expires on the release date of a certificate of compliance with a later issue date, which may be necessary due to technical modifications or due to changes of standards, guidelines and directives.
This certificate of compliance covers all running machine models which are listed above and which are produced by h/p/cosmos on and from November 24, 2006. The validity of this certificate of compliance expires on the release date of a certificate of compliance with a later issue date, which may be necessary due to technical modifications or due to changes of standards, guidelines and directives.
Disposal [12.] By request and at the expense of the client h/p/cosmos might take over the disposal of old devices and devices not longer functioning. Please contact service@h-p-cosmos.com for a detailed offer. Note the information for possible disposal of the running machine parts or components through the client or a subcontractor.
After the instruction is completed the instruction protocol is to be signed by the h/p/cosmos technician and all trained persons and sent back, together with the signed delivery note and the registration form, to h/p/cosmos.
Page 168
Explanation of test-mode and the integrated test-programs, inform about interface and compatibility list. In medical field potential isolation for any interface linkage is obligatory! Inform about the h/p/cosmos software programs h/p/cosmos para control, h/p/cosmos para graphics, h/p/cosmos para analysis and h/p/cosmos para motion for documentation and evaluation of data.
[04] Lubrication of running belt when "OIL"-message (quantity, intervals according to instruction manual, spread the oil by "Duck-walking"). Use only original h/p/cosmos lubricant authorized for this model of running machine. Observe demand for additional lubrication based on manual. After running belt lubrication the position of the running belt must be checked once more and be adjusted if necessary.
[14.D] [01] Hand over and explain delivery papers (folder). Fill out registration form and send it to h/p/cosmos sales. Let the customer sign the delivery note and instruction protocol and send it back to h/p/cosmos sales immediately. Ask for brochure of customer and send it to the sales department at h/p/cosmos.
Please fill out the instruction protocol and send back to h/p/cosmos via Fax to +49 / 86 69 / 86 42 49, via email to sales@h-p-cosmos.com or via post h/p/cosmos sports &...