Table of Contents
Advertisement
Table 5-7 Integrated Peripherals menu (continued)
Items
Onboard LAN
Device
IDE HDD Block
Mode
Onboard Lan
Boot ROM
Onboard FDC
Controller
Onboard Serial
Port 1/2/3/4
Onboard Serial
Port 5/6, Serial
Port 5/6 Use IRQ
Onboard
Parallel Port
5-12 BIOS Functions
Description
This setting enables/disables the network controller housed in the chip set (ICH2).
The default setting is "Enabled".Perform setting (using or not using the network controller)
according to your system configuration.
Enabled: Choose this if the network controller built in the chip set (ICH2) is used.
Disabled: Choose this if the network controller built in the chip set (ICH2) is not used.
The IRQ resources for the network controller are allocated as follows:
Enabled: PnP BIOS automatically allocates IRQ resources.
Disabled: IRQ resources are not allocated.
This setting enables/disables the IDE-HDD multi-sector transfer mode.
The default setting is "Enabled". Always use the default setting.
Enabled: Choose this to set the multi-sector transfer mode.If data is stored extending over
continuous sectors, performance will improve.
Disabled: This sets the single sector transfer mode.
This setting enables/disables the PXE Boot Agent function.
When the Onboard LAN Device is "Disabled", the Onboard Lan Boot ROM setting does not
function. The default setting is "Enabled".
Enabled: Choose this if the PXE Boot Agent function is used.
Disabled: Choose this if the PXE Boot Agent function is not used.
When OS mistakes the PCI I/F Card, it is possible to avoid in setting "Disabled".
When "Disabled"setting, the PXE Boot Agent function cannot be used.
This setting enables/disables the floppy controller inside the S-I/O (W83627).
The default setting is "Enabled". Always use the default setting.
Enabled:
Choose this if the FDD is used.
Disabled:
Choose this if the FDD is not used.
This setting enables/disables serial controller #1/2/3/4 (combination of the I/O address and IRQ
resource for serial port #1) inside the S-I/O (W83627).
The default setting are as follows.
Serial Port 1 : 3F8/IRQ4
Serial Port 2 : 2F8/IRQ3
Serial Port 3 : 3E8/IRQ11
Serial Port 4 : 2E8/IRQ10
There are options, the "3F8/IRQ4" setting, " 2 F8/IRQ 3 " setting, "3 E 8/IRQ4" setting, " 2E 8/IRQ 3 "
setting, "3F8/IRQ 11 " setting, " 2 F8/IRQ 10 " setting, " 3E 8/IRQ 11 " setting, " 2E 8/IRQ 10 " setting, "3 3 8/
IRQ 11 " setting, " 23 8/IRQ 10 " setting, and " Disabled " setting .
Make the necessary changes in accordance with the system configuration.
This setting enables/disables serial controller #5/6 (combination of the I/O address and IRQ
resource for serial port #1) inside the S-I/O (W83697UF).
The default setting is "Disabled".
There are options of [Onboard Serial Port 5/6], the "3F8" setting, "2F8"setting, "3E8"setting,
"3E8"setting, "338"setting, "238"setting and "Disabled" setting.
There are options of [Serial Port 5/6 Use IRQ], the "IRQ3" setting, "IRQ4" setting, "IRQ5" setting,
"IRQ7" setting, "IRQ10" setting, "IRQ11" setting, "IRQ14" setting and "IRQ15" setting.
Make the necessary changes in accordance with the system configuration.
This setting enables/disables the parallel controller (combination of the I/O address and IRQ
resource for the parallel port) inside the S-I/O (W83627F).
The default setting is "378/IRQ7".
There are 4 options, the "Disabled" setting, "378/IRQ7" setting, "278/IRQ5" setting and the "3BC/
IRQ7" setting.
When using the "Disabled" setting, system resources can be opened and the port can be used
with other devices.
Make the necessary changes in accordance with the system configuration.
Note that since an 8-byte continuous I/O space is needed when setting the parallel port mode
to "EPP", the 3BC/IRQ7 setting cannot be used.
Rev.C
Advertisement
Table of Contents
