Download Print this page

Advertisement

DM-D500
Installation Guide
401467401

Advertisement

   Related Manuals for EPSON DM-D500

   Summary of Contents for EPSON DM-D500

  • Page 1

    DM-D500 Installation Guide 401467401...

  • Page 2

    Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to...

  • Page 3: Safety Precautions

    If water or other liquid spills into this equipment, immediately turn the power off and contact your dealer or a SEIKO EPSON service center for advice. Continued usage may lead to fire or shock.

  • Page 4: Cautions On Handling

    ❏ When connecting or disconnecting cables, make sure that the power switch of the DM-D500 and printers connected to the DM-D500 are turned off. ❏ Do not drop the DM-D500, because you may damage the built- in vacuum fluorescent display. Usage The DM-D500 can be used with the following equipment.

  • Page 5

    (DP-105) is required. (See page 21.) Precautions When Connecting to a TM Printer Before the DM-D500 is connected to a TM printer, check the serial number on the label affixed to the rear or bottom of the TM printer. If the serial number is one of the numbers listed in the following table, the printer can be connected to the DM-D500 without an additional board.

  • Page 6

    If the RS-232 interface of the TM printer or the UB-S01 board has a blue seal or a scribed square (as shown in illustrations 2 and 3), it can be connected to the DM-D500 without an additional board. blue seal...

  • Page 7

    TM-J8000 printer using the “DM-D pole unit for TM printers (Type B)” (DP-503). Required items The items shown in illustration 4 are used to attach the DM-D500 to a TM-H5000II or TM-J8000 printer. These items are packed with the “DM-D pole unit for TM printers (Type B)” (DP-503).

  • Page 8

    TM printer, and secure it with the screws as shown in illustration 7. 3. Pass the cable for the DM-D500 through the base as shown in illustration 8. 4. Insert the tab on the base into the hole on the support as shown in illustration 9 until you feel it click.

  • Page 9

    English Attaching to the TM-U950 The DM-D500 can be attached directly to a TM-U950 printer using the “DM-D pole unit for TM printers (Type A)” (DP-502). Required items The items shown in illustrations 11 or 12 are used to attach a DM-D500 to a TM-U950 printer.

  • Page 10

    English Assembling 1. Pass the cable for the DM-D500 through support C, and attach support C to the DM-D500 as shown in illustration 13. When using support B for extension, insert the tab on support B into the hole on support C as shown in illustration 14 until you feel it click.

  • Page 11

    19. Attaching to the TM-H6000 Series or TM-U675 The DM-D500 can be attached directly to a TM-H6000 series or TM- U675 printer using the “DM-D pole unit for TM printers (Type A)” (DP-502). You can attach fixing plate A on either side of the TM-H6000 series or TM-U675.

  • Page 12

    English Required items The items shown in illustration 20 are used to attach the DM-D500 to TM-H6000 series or TM-U675 printers. These items are packed with the “DM-D pole unit for TM printers (Type A)” (DP-502). fixing screw angle fixing...

  • Page 13

    2. Attach the rubber feet to the printer as shown in illustration 23. 3. Attach fixing plate B to the printer as shown in illustration 24. 4. Pass the cable for the DM-D500 through the hole on fixing plate A, and fix the cable at the bottom as shown in illustration 25.

  • Page 14

    English 5. Connect the cable for the DM-D500 to the DM connector on the TM printer as shown in illustration 26. 6. Attach fixing plate A to the TM printer using the stopper. When you attach the stopper, insert the projections on the stopper into the holes of fixing plate B.

  • Page 15

    7. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to one of the four positions shown in illustration 28, 29, 30, or 31, and secure it with the angle fixing screw. DM-D500 Installation Guide 13...

  • Page 16

    B, as shown in illustration 34. Attaching to the TM-T88II, TM-U210, TM-U230, TM-T90, or TM-L90 The DM-D500 can be attached to a TM-T88II, TM-U210, TM-U230, TM-T90, or TM-L90 printer using the “DM-D pole unit for TM printers” (DP-505). 14 DM-D500 Installation Guide...

  • Page 17

    English Required items The items shown in illustration 35 are used to attach a DM-D500 to a TM-T88II, TM-U210, TM-U230, TM-T90, or TM-L90 printer. These items are packed with the “DM-D pole unit for TM printers” (DP-505). support extension fixing plate...

  • Page 18

    37 until you feel it click. when using an extension support 4. Pass the cable for the display through the hole on the fixing plate, and attach the support to the fixing plate as shown in illustration 38. 16 DM-D500 Installation Guide...

  • Page 19

    TM printer (UB-S09) until you feel it click as shown in illustration 41. Store any excess cable in the TM printer, if necessary. TM-T88II printer with the UB-S09 installed CAUTION: Do not connect this connector to an ordinary telephone line. DM-D500 Installation Guide 17...

  • Page 20: Attaching To Other Tm Printers

    3. Follow steps 7 to 9 in “Assembling using Velcro tapes.” Attaching to Other TM Printers When using with other TM printers, the DM-D500 can be attached to a desk or other surface using the “DM-D pole unit for TM printers (Type A)”...

  • Page 21

    English Required items The items shown in illustration 44 are used when the DM-D500 is used with other TM printers. These items are packed with the “DM-D pole unit for TM printers (Type A)” (DP-502). Velcro tapes Velcro tapes fixing plate A...

  • Page 22

    1. Follow steps 2 and 3 in “Assembling using Velcro tapes.” 2. Secure fixing plate A to the setting position with fixing screws as shown in illustration 51. 3. Attach the DM-D500 to fixing plate A. 20 DM-D500 Installation Guide...

  • Page 23

    English Attaching to the DM-D Stand The DM-D500 can be attached directly to the DM-D stand using the “DM-D stand unit for DM-D500” (DP-501). The DM-D500 with the DM-D stand can be connected to a TM printer or be used as a standalone product.

  • Page 24: Jumper Settings

    Set the jumpers on the DM-D stand as follows: Contents When connecting both the TM printer and the DM-D stand. (Default setting.) When using the DM-D stand as a standalone. (TM printer is not connected.) The jumpers are located as shown in illustration 57. 22 DM-D500 Installation Guide...

  • Page 25

    English Precautions on using the power supply unit To avoid damage to the DM-D500 and the power supply unit, note the following points. ❏ Use the optional Seiko Epson product, PS-180, as the power supply. ❏ Never connect the DC cable to the power supply unit when the power supply unit is connected.

  • Page 26

    English 3. Connect the cable for the DM-D500 to the display connector on the DM-D stand as shown in illustration 61 until you feel it click. 4. Connect one end of the computer interface cable to the computer connector on the DM-D stand; then connect the other end to the RS-232 connector on the computer as shown in illustration 62.

  • Page 27

    (with the arrow mark up) to the extension cable connector indicated with “POWER OUT” on the DM-D stand; then connect the other end to the power connector on the printer as shown in illustration 64. extension cable connector extension cable for power supply DM-D500 Installation Guide 25...

  • Page 28

    9. Arrange the cables as shown in illustration 66. Put the cables for the DM-D500 inside the DM-D stand. 10. Attach the base plate to the DM-D stand following the numbers of the arrows shown in illustration 67. Then, push the base plate until it is locked by the hook on the DM-D stand.

  • Page 29: Part Names And Functions

    ❏ Power switch: The power is turned on/off. ❏ DIP switch: The functions of the DM-D500 are changed. See “DIP Switch” for details. Note: When turning on the DM-D500 again after turning it off, wait for at least 3 seconds. DM-D500 Installation Guide 27...

  • Page 30

    (*1) XON/XOFF is effective only when the DM-D500 is connected as a standalone. Transmission speed* SW1-6 SW1-7 SW1-8 Transmission speed (bps) 2400 4800 9600 19200 38400 57600 115200 *When the DM-D500 is connected to a TM printer, be sure that the transmission speed matches that of the printer. 28 DM-D500 Installation Guide...

  • Page 31

    DM-D105/106/205/206. In this case, the graphic display and the original functions for the DM-D500 cannot be used; however, by selecting “256 × 64 dots mode,” they can be used. (*4) When setting to “Printer is selected,” data is sent to the TM printer, but is not displayed on the display.

  • Page 32

    English Turning and Tilting the DM-D500 You can turn or tilt the display while holding the support. The display can be moved easily, so do not move it any further if it stops. If you move it by force, you may damage it.

  • Page 33: Specifications

    Storage: 30% to 90% (no condensation) Overall dimensions See figures below. Weight (mass) DM-D500: 460 g {1.01 lb}, DP-501: 440 g {0.97 lb}, DP-502: 264 g {0.58 lb}, DP-503: 116 g {0.26 lb}, DP-505: 418 g {0.92 lb} DM-D500 Installation Guide 31...

  • Page 34

    English <DM-D500 and DM-D stand> 213 mm {8.4"} DM-D500 83 mm {3.3"} 65 mm {2.6"} DM-D stand (DP-501) 51 mm {2.0"} 200 mm {7.9"} 48° 118 mm {4.7"} 90° 32 DM-D500 Installation Guide...

  • Page 35

    (DP-503) 260 mm 248 mm {10.2"} {9.8"} 164 mm {6.5"} 78 mm 50 mm base {3.1"} {1.9"} DM-D pole unit for 53 mm TM printers (DP-505) 260 mm {2.1"} {10.2"} 130 mm {5.1"} 214 mm {8.4"} DM-D500 Installation Guide 33...

  • Page 36

    English 34 DM-D500 Installation Guide...

Comments to this Manuals

Symbols: 0
Latest comments: