Download Print this page

Advertisement

Customer Display
DM-D110
Installation Manual
401285001

Advertisement

   Also See for Epson DM-D110 - Vacuum Fluorescent Display Character

   Related Manuals for Epson DM-D110 - Vacuum Fluorescent Display Character

   Summary of Contents for Epson DM-D110 - Vacuum Fluorescent Display Character

  • Page 1

    Customer Display DM-D110 Installation Manual 401285001...

  • Page 2

    Neither is any liability assumed for damages resulting from the use of the information contained herein. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred...

  • Page 3: Safety Precautions

    If water or other liquid spills into this equipment, immediately turn the power off and contact your dealer or a SEIKO EPSON service center for advice. Continued usage may lead to fire or shock.

  • Page 4

    EMC and Safety Standards Applied Product Name: DM-D110 Type Name: M58DB The following standards are applied only to the display that is so labeled. (EMC is tested using the EPSON PS-170 power supply.) Europe: CE Marking Safety: EN60950 North America: EMI: FCC/ICES-003 Class A Safety: UL 1950/CSA C22.2 No.950...

  • Page 5: About This Manual

    WARNING You are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could void your authority to operate the equipment. FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

  • Page 6: Table Of Contents

    Contents About This Manual ............3 Contents .

  • Page 7: Unpacking

    This manual explains how to set up the DM-D110. Unpacking The following items are in the box. installation manual Display (DM-D110) Make sure that you have all the items shown above, and that none has been damaged. If you find anything missing or damaged items, please contact your DM-D110 dealer.

  • Page 8: Usage

    Usage The DM-D110 can be used with the following equipment. IM series. You can attach the DM-D110 to the IM series using the “DM-D pole unit for IR” (DP-504). (See page 7.) TM-H5000II/TM-J8000 printers. You can attach the DM-D110 to TM-H5000II/TM-J8000 printers using the “DM-D pole unit for TM printers (Type B)”...

  • Page 9: Assembling

    Assembling Attaching to the IM series The DM-D110 can be attached directly to the IM series using the “DM-D pole unit for IR” (DP-504). Required items The following items are used to attach the DM-D110 to the IM series. These items are packed with the “DM-D pole unit for IR” (DP-504). fixing screws base support A...

  • Page 10

    2. Attach the base to the setting position on the IM series, and secure it with the screws. Note: When attaching the base, note that the corners of the base are set as shown below. 3. Pass the cable for the DM-D110 through the base. 4.

  • Page 11: Attaching To The Tm-h5000ii/tm-j8000

    5. Connect the cable for the DM-D110 to the DM connector on the IM series. Attaching to the TM-H5000II/TM-J8000 The DM-D110 can be attached directly to the TM-H5000II/TM-J8000 printers using the “DM-D pole unit for TM printers (Type B)” (DP-503). Required items The following items are used to attach the DM-D110 to the TM-H5000II/TM-J8000 printers.

  • Page 12

    Assembling steps 1. Pass the cable for the DM-D110 through support C, and attach support C to the DM-D110. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2.

  • Page 13

    3. Pass the cable for the DM-D110 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click. 5. Connect the cable for the DM-D110 to the DM connector on the TM printer.

  • Page 14: Attaching To The Tm-u375/tm-u950

    Attaching to the TM-U375/TM-U950 The DM-D110 can be attached directly to the TM-U375/TM-U950 printers using the “DM-D pole unit for TM printers (Type A)” (DP-502). Required items The following items are used to attach the DM-D110 to the TM-U375/ TM-U950 printers. These items are packed with the “DM-D pole unit for TM printers (Type A)”...

  • Page 15

    Assembling steps 1. Pass the cable for the DM-D110 through support C, and attach support C to the DM-D110. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2.

  • Page 16

    3. Pass the cable for the DM-D110 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 4. Connect the cable for the DM-D110 to the DM connector on the TM printer. 5. Adjust the length of the cable and secure fixing plate A to the printer with screws.

  • Page 17: Attaching To The Tm-h6000/tm-u675

    6. Store any excess cable in the support, and attach the DM-D110 to fixing plate A. Attaching to the TM-H6000/TM-U675 The DM-D110 can be attached directly to the TM-H6000/TM-U675 printers using the “DM-D pole unit for TM printers (Type A)” (DP-502).

  • Page 18

    Assembling steps 1. Pass the cable for the DM-D110 through support C, and attach support C to the DM-D110. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 2.

  • Page 19

    4. Pass the cable for the DM-D110 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 5. Connect the cable for the DM-D110 to the DM connector on the TM printer. 6. Attach fixing plate A to the TM printer using the stopper. When you attach the stopper, insert the projections on the stopper into the holes of fixing plate B.

  • Page 20

    7. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw.

  • Page 21

    Note: The paper roll cover may not open if the position of the display is inappropriate. Before securing the position of the display, make sure that you can open the paper roll cover. paper roll cover 8. Store any excess cable in the support and attach the DM-D110 to fixing plate A.

  • Page 22: Attaching To Other Tm Printers

    Attaching to Other TM Printers When using with other TM printers, the DM-D110 can be attached to a desk or other surface, using the “DM-D pole unit for TM printers (Type A)” (DP-502), and Velcro tapes or screws. Required items The following items are used when the DM-D110 is used with other TM printers.

  • Page 23

    2. Pass the cable for the DM-D110 through support C, and attach support C to the DM-D110. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. When using support B for extension 3.

  • Page 24

    5. Store any excess cable in the support, and attach the DM-D110 to fixing plate A. 6. Peel off the Velcro tapes, and attach the display to the setting position. Assembling steps using screws 1. Follow steps 2 and 3 in “Assembling steps using Velcro tapes.” 2.

  • Page 25: Attaching To The Dm-d Stand

    Attaching to the DM-D stand The DM-D110 can be attached directly to the DM-D stand using the “DM-D stand unit for DM Customer Display” (DP-110). The DM-D110 with the DM-D stand can be connected to a TM printer, or be used as a stand alone product.

  • Page 26

    Connectors for the DM-D stand The connectors for the DM-D stand are as follows: display connector computer connector printer connector extension cable connector power supply unit connector Note: The DM-D stand comes with inch-type hexagonal lock screws installed to secure the interface cable to the interface connector for RS-232. If you plan to use an interface cable which requires millimeter-type lock screws, replace the inch-type screws with the included millimeter-type screws using a hex screwdriver (5mm).

  • Page 27

    To avoid damage to the DM-D110 and the power supply unit, make sure to note the following points. Use the optional Seiko Epson products, PS-170, or PA-6508, PA-6511, PA-6513, PB-6509 or PB-6510 as the power supply. Never connect the DC cable to the power supply unit when the power supply unit is connected.

  • Page 28

    Assembling steps 1. Pass the cable for the DM-D110 through the DM-D stand. When extending the length of the DM-D stand, attach the extension support (DP-105) to the DM-D stand. When using the extension support (DP-105) Insert the tab on the DM-D110 (or the extension support) into the hole on the DM-D stand until you feel it click.

  • Page 29

    3. Connect the cable for the DM-D110 to the display connector on the DM-D stand until you feel it click. 4. Connect one end of the computer interface cable to the computer connector on the DM-D stand; then connect the other end to the RS-232 connector on the computer.

  • Page 30

    5. When using as a stand alone, go to step 6. When using with the printer, connect one end of the printer interface cable for the printer to the printer connector on the DM-D stand; then connect the other end to the connector on the printer. Tighten the screws on both ends of the cable to fasten them.

  • Page 31

    7. Connect the DC cable of the power supply unit (with the arrow mark up) to the power supply unit connector indicated with “POWER IN” on the DM-D stand. power supply unit connector DC cable of power supply unit 8. When using as a stand alone product, set the jumpers. (See “Jumper setting”...

  • Page 32

    10. Attach the base plate to the DM-D stand following the number of the arrow shown below. At this time, push the base plate until it is locked by the hook on the DM-D stand. 11. When the extension support (DP-105) is used, attach Velcro tapes to the four corners of the plate to avoid falling down.

  • Page 33: Part Names And Functions

    Part Names and Functions Exterior DIP switch display (rear side of the display) power switch (bottom of the display) Display: Characters are displayed. Power switch: The power is turned on/off. DIP switch: The functions of the DM-D110 are changed. (See “DIP switch” for details.) Note: When turning on the DM-D110 again after turning it off, wait for at least 3 seconds.

  • Page 34: Dip Switch

    DIP Switch DIP Switch Functions The DM-D110 has one DIP switch. The functions of the DIP switch are as follows: DIP switch 1 DSW1 No. Function Default setting Data receive error Ignored Displays “?” Data length 7 bits 8 bits Parity on or off Parity No parity...

  • Page 35

    Setting the DIP switches CAUTION: Turn off the DM-D110 while removing the DIP switch cover to prevent electrical damage to the DM-D110. 1. Turn off the power for the DM-D110. 2. Remove the DIP switch cover. DIP switch cover 3. Change each setting of the switches with a pointed object, such as a pen tip or small screwdriver.

  • Page 36: Turning And Tilting The Dm-d110

    Turning and Tilting the DM-D110 You can turn or tilt the display while holding the support. The display can be moved easily, so do not move any further if it stops. If you move it by force, you may damage it. With the “DM-D pole unit for IR”...

  • Page 37: Self Test

    Self Test The DM-D110 has a self test function. If you want to perform a self test, you must change the setting of the DIP switch. Check Items of Self test The following items are checked during the self test: Control ROM version DIP switch settings Memory switch settings...

  • Page 38: Specification

    Specification General Specifications Height, Width, Depth and Weight <DM-D110 and DM-D stand> DM-D110 DM-D stand (DP-110) • DM-D110: Height: 69 mm Width: 165 mm Depth: 50.5 mm Weight: 285 g • DM-D stand (DP-501): Height: 63 mm Width: 165 mm Depth: 110 mm Weight:...

  • Page 39

    <DM-D pole units> DM-D pole unit for DM-D pole unit for TM printers (Type A) TM printer (Type B) DM-D pole unit for IR (DP-502) (DP-503) (DP-504) 129 mm 260 mm 248 mm 164 mm 78 mm 50 mm base 53 mm •...

  • Page 40: Electrical Specifications

    Tilt angle Max 48 (4 steps, 5 positions) Horizontal rotation Max 90 (for each left and right at 45 ) Vacuum fluorescent display • Number of characters: 20 column 2 lines max. • Display color: Green (505 nm) • Brightness: 690 (cd/m Electrical Specifications Type...

  • Page 41: Character Specifications

    Character Specifications Type of character • Alphanumeric characters: 95 • International characters: • Extended graphics: 128 characters 12 pages Character grid • Font : 7 dot, cursor • Character size 3.5 mm x 5.0 mm • Character pitch 5.2 mm Reliability Specification MTBF (vacuum fluorescent display only) 20,000 hours...

Comments to this Manuals

Symbols: 0
Latest comments: