Cisco AP776A - Nexus Converged Network Switch 5020 Configuration Manual page 318

Upgrading the SSI Boot Image
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
Note
Note
Issue the show boot command to display the current contents of the image boot variable for the SSM.
Step 5
switch# show boot
sup-1
kickstart variable = bootflash:/boot-2-0-1-9
system variable =
bootflash:/isan-2-0-1-9;bootflash:/isan-2-0-0-181b;bootflash:/isan-2-0-0-181b
sup-2
kickstart variable = bootflash:/boot-2-0-1-9
system variable =
bootflash:/isan-2-0-1-9;bootflash:/isan-2-0-0-181b;bootflash:/isan-2-0-0-181b
Module 4
ssi variable = modflash://4-1/m9000-ek9-ssi-mz.2.1.2.bin
Save the new boot variable configuration so the new boot image is used when the switch reboots.
Step 6
switch# copy running-config startup-config
Note
Step 7 Issue the show module command to verify the status of the SSM.
switch# show module
Mod
---
4
5
6
Mod
---
4
5
6
Mod
-------- -----------------------------
4
Mod
---
4
5
6
Cisco MDS 9000 Family CLI Configuration Guide
12-26
If the SSM is configured for Layer 3 Fibre Channel switching or Intelligent Storage Services, a
warning will be displayed at the command prompt indicating that the operation will disrupt
traffic and you will be asked if you wish to continue.
As of Cisco MDS SAN-OS Release 2.1(2), we recommend that you reference the SSI boot image
on modflash: on the SSM. Use the install ssi modflash://slot-1/filename module slot command
to install the SSI image.
If you do not save this configuration, it is lost on a switch reboot. In addition, SSM stays in the
power-down state if your switch is running Cisco MDS SAN-OS Release 2.1(1a) or earlier, or
comes up in Fibre Channel switching mode if your switch is running Cisco MDS SAN-OS
Release 2.1(2) or later. You must perform this procedure again to recover the SSI image boot
variable configuration.
Ports Module-Type
----- -------------------------------- ------------------ ------------
32 Storage Services Module
0 Supervisor/Fabric-1
0 Supervisor/Fabric-1
Sw Hw World-Wide-Name(s) (WWN)
----------- ------ --------------------------------------------------
2.1(2) 0.30 20:c1:00:05:30:00:06:de to 20:e0:00:05:30:00:06:de
2.1(2) 4.0 --
2.1(2) 4.0 --
Application Image Description
SSI linecard image
MAC-Address(es)
--------------------------------------
00-05-30-00-9e-b2 to 00-05-30-00-9e-b6
00-0e-38-c6-2c-6c to 00-0e-38-c6-2c-70
00-0f-34-94-4d-34 to 00-0f-34-94-4d-38
Chapter 12
Model Status
DS-X9032-SSM ok
DS-X9530-SF1-K9 active *
DS-X9530-SF1-K9 ha-standby
Application Image Version
-------------------------
2.1(2)
Serial-Num
----------
JAB06480590
JAB082504MQ
JAB083407D3
OL-18084-01, Cisco MDS NX-OS Release 4.x
Managing Modules