Ether; Fire Extinguisher; Fire Safety - Vanguard CPW 125-4-S Series Operation And Maintenance Manual

Ether

Ether (if equipped) is commonly used in cold-weather applications. Ether is flammable and poisonous.
Follow the correct cold engine starting procedures. Refer to the Operation and Maintenance Manual, "Ether Starting Aid".
Do not spray ether manually into an engine if the machine is equipped with a thermal starting aid for cold weather starting.
Use ether in ventilated areas. Do not smoke while you are replacing an ether cylinder or while you are using an ether spray.
Do not store ether cylinders in living areas or in the operator compartment of a machine. Do not store ether cylinders in
direct sunlight or in temperatures above 40°C (102°F). Keep ether cylinders away from open flames or sparks.
Dispose of used ether cylinders properly, and only in an approved place. Do not puncture an ether cylinder. Do not burn
ether cylinders. Keep ether cylinders away from unauthorized personnel.

Fire Extinguisher

A fire extinguisher is typically carried on the vehicle carrier. As an additional safety measure, keep a fire extinguisher on the
machine.
Be familiar with the operation of the fire extinguisher. Inspect the fire extinguisher and service the fire extinguisher
regularly. Obey the recommendations on the fire extinguisher's instruction-plate.
Note: Keep access and walkway clear; do not mount any accessory equipment in a manner that obstructs the access or
walkways.
If an additional extinguisher is required on the weld-deck, mount one in a convenient and readily accessible location, such as
the free deck-space to the rear of the control/distribution center beside the transformer, or in the space between the tractor
and the welding power-unit enclosure.
Consider installation of an aftermarket Fire Suppression System, if the application and working conditions warrant the
installation.

Fire Safety

Note: Locate secondary exits and how to use the secondary exits before you operate the machine.
Note: Locate fire extinguishers and how to use a fire extinguisher before you operate the machine.
If you find that you are involved in a machine fire, your safety and that of others on site is the top priority. The following
actions should only be performed if the actions do not present a danger or risk to you and any nearby people. At all times
you should assess the risk of personal injury and move away to a safe distance as soon as you feel unsafe.
Move the machine away from nearby combustible material such as fuel/oil stations, structures, trash, mulch and timber.
Lower any implements and turn off the engine as soon as possible. If you leave the engine running, the engine will continue
to feed a fire. The fire will be fed from any damaged hoses that are attached to the engine or pumps. Use the emergency Stop
button on the welder package; refer to Operation and Maintenance Manual, "Emergency Stop" for specific instructions.
If possible, turn the battery disconnect switch to the OFF position. Disconnecting the battery will remove the ignition source
in the event of an electrical short. Disconnecting the battery will eliminate a second ignition source if electrical wiring is
damaged by the fire, resulting in a short circuit.
Notify emergency personnel of the fire and your location.
If your machine is equipped with a fire suppression system, follow the manufacturer's procedure for activating the system.
Note: Fire suppression systems need to be regularly inspected by qualified personnel. You must be trained to operate the fire
suppression system.
Use the on-board fire extinguisher, per the instructions on the fire extinguisher's instruction-plate, use the following
procedure:
1. Pull the pin.
2. Aim the extinguisher or nozzle at the base of the fire.
3. Squeeze the handle and release the extinguishing agent.
4. Sweep the extinguisher from side to side across the base of the fire until the fire is out.
Remember, if you are unable to do anything else, shut off the machine before exiting. By shutting off the machine, fuels will
not continue to be pumped into the fire. Use the emergency Stop button on the welder package to shut off the machine.
037-08OP-002D-01 S/N CB50600021 – UP (Weld-deck)
28