B&R Automation PC 3100 User Manual page 165

BIOS parameter
PCH PCIe CLKREQ# mapping override
CLKREQ number
Table 191: Advanced - PCH-IO configuration - PCI Express root port n
1) PCI Express root port n must be enabled in order to make further configurations.
2) Upstream port transmitter preset
The default value is system-optimized by B&R.
3) Downstream port transmitter preset
The default value is system-optimized by B&R.
4) Changes to the ACS have no effect on the display of the following indented parameters.
5) With a multifunction device, all functions within the device are monitored.
For the root port, the error occurs within the root complex.
6) Generates a system error if an error of this category is reported by a root port or device on a root port.
4.1.7.2.9.2 SATA and RST configuration
BIOS parameter
SATA controller(s)
1)
SATA mode selection
SATA test mode
RAID device ID
Software feature mask configuration
Aggressive LPM support
Serial ATA port n
Software preserve
Port n
Hot plug
Configured as eSATA
Spin up device
SATA device type
Topology
SATA port n DevSlp
DITO configuration
DITO value
DM value
Table 192: Advanced - PCH-IO configuration - SATA and RST configuration
1) SATA controller(s) must be enabled to be able to make additional configurations.
2) This submenu can only be configured if "SATA test mode" is enabled.
3) n corresponds to the available SATA ports that are indexed from 0 to n-1.
Software feature mask configuration
BIOS parameter
HDD unlock
LED locate
Use RST legacy OROM
Table 193: Advanced - PCH-IO configuration - SATA and RST configuration - Software feature mask configuration
Automation PC 3100 User's manual V 1.00 Translation of the original documentation
Setting options Description
Custom number Disables the clock request number for standard platform mapping or uses the default
values or manual value
Default
No CLKREQ
INT Defines the CLKREQ number
Default: 0 Range: 0 to 15
Setting options Description
Disabled Disables/Enables the SATA controller
Enabled
AHCI Select SATA mode AHCI (not RAID) or Optane (or RAID)
See
Intel RST premium
with Intel Optane
Disabled Disables/Enables the test function
This is only used for control measurements.
Enabled
Alternate Selects the RAID device ID mode
Client
Enter Opens submenu
2)
Disabled Disables/Enables Aggressive Link Power Management
The host controller can change to a low-power state in the idle phase of the SATA device.
Enabled
- Displays the name and capacity of the SATA device
- Displays support for the software preserve
Disabled Disables/Enables SATA port n
Enabled
Disables/Enables hot plugging
Disabled
Enabled
- Displays hot plugging support of the device on the SATA port
Disabled Disables/Enables spin up for the connected device on the SATA port
Enabled
Hard disk drive Defines the SATA device type as HDD or SSD
Solid-state drive
Unknown Defines the SATA topology
ISATA
Direct connect
Default for port 0 and 1
Flex
M2
Default for port 2
Disabled Disables/Enables for the device on port n
Enabled
Disables/Enables device sleep idle timeout
Disabled
Enabled
INT Defines the DITO value [ms]
Default: 625 Range: 0 to 1023
INT Defines the DITO multiplier
Default: 15 Range: 0 to 15
Setting options Description
Disabled Disables/Enables HDD unlock
The HDD can be locked in the operating system by a password.
Enabled
Disabled Disables/Enables LED locate
Indicates that LED/SGPIO hardware is connected and pingable.
Enabled
Disables/Enables rapid storage technology legacy option ROM for active CSM
Disabled
Enabled
"RAID configuration" on page 180.
"Software feature mask configuration" on page 165
Software
1)
165