JLG 1850SJ Service And Maintenance Manual page 124

SECTION 3 - CHASSIS & TURNTABLE
Deutz Blink
SPN FMI
Code Code
616 555 523612 12
617 555 523612 12
618 555 523612 12
619 555 523612 12
620 555 523612 12
621 555 523612 12
623 555 523612 12
624 555 523612 12
625 555 523612 12
627 555 523612 12
628 555 523612 12
629 555 523612 12
3-74
Table 3-10. Engine Fault Codes
Description
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
Internal hardware monitoring: the CPU of
the ECU is reset and the cause is logged inter-
nally; no item will be created in error mem-
ory
The two voltage values (ADC_VAL1,
ADC_VAL2), detected by
the accelerator pedal, are not plausible to
each other.
Possible Cause
Error report due to an interrupted SPI communi-
cation (ECU internal error)
multiple error in complete ROM-test during
postdrive detected (ECU internal error)
Too less bytes received by monitoring memory
from CPU as response (ECU internal
error). Loss of synchronization sending bytes to
the monitoring memory from CPU
Suspected components:
Injector
ECU
wiring harness/connector
Error trying to set MM Response time (ECU
internal error)
Error detected in the internal ECU communica-
tion, Too many SPI errors during
MoCSOP execution
Error in the check of the shut-off path test of the
under voltage detection (ECU internal
error). Diagnostic fault check to report the error
in undervoltage monitoring
Error in the check of the shut-off path of the
monitoring module (ECU internal error).
Time out error trying to set or cancelling the
alarm task (ECU internal error). Failure
setting the alarm task period
Error in time monitoring of the shut-off path
test (ECU internal error). Diagnostic fault
check to report the timeout in the shut
off path test
Error in the check of the shut-off path test of the
over voltage detection (ECU internal
error). Diagnostic fault check to report the error
in overvoltage monitoring
Defect pedal or wiring
Action
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
If error is still present, exchange ECU.
Threshold for error detection is an internal ECU
threshold.
Check Pedal, repair or exchange the Pedal.
Check wiring.
If error is still present, exchange ECU.
3121619