JLG 1850SJ Service And Maintenance Manual page 118

SECTION 3 - CHASSIS & TURNTABLE
Deutz Blink
SPN FMI
Code Code
140 767 523941 9
141 767 523942 9
142 767 523943 9
168 763 523935 12
169 764 523936 12
171 3-3-3 523212 9
179 527 523240 9
291 119 523776 9
292 119 523777 9
305 118 898 9
360 737 523982 0
361 737 523982 1
3-68
Table 3-10. Engine Fault Codes
Description
Timeout Error (BAM to packet) for CAN-
Receive-Frame AT1OGCVol2 information;
factors & Sensorcalibration for NOX Sensor
(SCR-system downstream cat; DPF-system
downstream cat)
Timeout Error (BAM to BAM) for CAN-
Receive-Frame AT1OGCVol2 information,
Calibration message 1 of the after catalyst
NOx sensor has failed.
Factors & Sensorcalibration for NOX Sensor
(SCR-system downstream cat, DPF-system
downstream cat)
Timeout Error (PCK2PCK) for CAN-Receive-
Frame AT1OGCVol2 information; factors &
Sensorcalibration for NOX Sensor (SCR-sys-
tem downstream cat; DPF-system
downstream cat)
Timeout Error of CAN-Transmit-Frame
EEC3VOL1; Engine send messages
Timeout Error of CAN-Transmit-Frame
EEC3VOL2; Engine send messages
Timeout Error of CAN-Receive-Frame
ComEngPrt; Engine Protection
Timeout CAN-message FunModCtl; Func-
tion Mode Control
Timeout Error of CAN-Receive-Frame TSC1TE
- active
Message TSC1-TE has been missing (passive) Passive timeout Error (Missing CAN Bus mes-
Timeout Error of CAN-Receive-Frame TSC1TE
- active
Powerstage diagnosis disabled; Indicating
that battery voltage is not high.
Powerstage diagnosis disabled; Indicating
that battery voltage is not low.
Possible Cause
Timeout Error (Missing CAN Bus message)
Defective Nox sensor, faulty parameterization. NOX downstream sensor and sensor connection
The fault is detected when a timeout error in
packet 2 of NOxSenVol2Rx frame occurs.
Fault is detected if a TimeOut of the EEC3VOL1
frame has occured.
Timeout Error (Missing CAN Bus message)
Timeout Error (Missing CAN Bus message)
Timeout Error (Missing CAN Bus message)
Timeout Error (Missing CAN Bus message)
sage)
Timeout Error (Missing CAN Bus message)
Powerstage diagnostic can be deactivated due
to too high battery voltage.
Powerstage diagnostic can be deactivated due
to too low battery voltage.
Action
NOX downstream sensor and sensor connection
check
check.
NOX downstream sensor and sensor connection
check
Check wiring harness and customer nodes
Check wiring harness and customer nodes
Check wiring harness and customer devices
Check CAN Bus cabling (Bus sheduling, polarity,
short circuit, power interrupt), test
protocol of receiver, check CAN functional
range.
Threshold for error detection is an internal ECU
threshold.
Check CAN Bus cabling (Bus sheduling, polarity,
short circuit, power interrupt), test
protocol of receiver, check CAN functional
range.
Check CAN Bus cabling (Bus scheduling, polar-
ity, short circuit, power interrupt), test
protocol of receiver, check CAN functional
range, check actuator
Check CAN Bus cabling (Bus sheduling, polarity,
short circuit, power interrupt), test
protocol of receiver, check CAN functional
range.
Check wiring, check alternator, check cables and
repair or replace if necessary.
Check wiring, check alternator, check cables and
repair or replace if necessary.
3121619