Pepperl+Fuchs IDENTControl IC-KP2-2HB18-2V1 Manual page 34

IC-KP2-2HB18-2V1
Commands
Description of the mechanical write data signal from master to slave (RY)
Address
RY(n+1)0-F /
RY(n+4)0-F
RY(n+2)0-F /
RY(n+5)0-F
RY(n+3)0-F /
RY(n+6)0-F
Description of the mechanical read data signal from slave to the master
(RX)
Address
RX(n+1)0-F /
RX(n+4)0-F
RX(n+2)0-F /
RX(n+5)0-F
RX(n+3)0-F /
RX(n+6)0-F
Addresses of the mechanical read data signal
CC-Link version: V 1.10
Cyclic setting: -
Channel 1 RX(n+1)0..F
.
.
.
RX(n+3)0..F
Channel 2 RX(n+4)0..F
.
.
.
RX(n+6)0..F
Addresses of the mechanical write data signal
CC-Link version:
Cyclic setting:
Channel 1
Channel 2
34
Signal name Description
mechanical The data of a write command is written to the address
flag write data area RY of the read/write tag if the mechanical flag
executionsignal is set.
The length of the words is dependent on the cyclic
settings. See also the table below, "Addresses of the
mechanical write data signal".
Signal name Description
mechanical If the master has set the mechanical flag execution
flag read data request signal, the data of the read/write tag is
formed on this signal.
V 2 V 2
single 2-way
RX(n+1)0..F RX(n+1)0..F
. .
. .
. .
RX(n+3)0..F RX(n+6)0..F
RX(n+4)0..F RX(n+7)0..F
. .
. .
. .
RX(n+6)0..F RX(n+C)0..F
V 1.10 V 2
- single
RY(n+1)0.. RY(n+1)0..
F F
. .
. .
. .
RY(n+3)0.. RY(n+3)0..
F F
RY(n+4)0.. RY(n+4)0..
F F
. .
. .
. .
RY(n+6)0.. RY(n+6)0..
F F
V 2 V 2
4-way 8-way
RX(n+1)0..F RX(n+1)0..F
. .
. .
. .
RX(n+C)0..F RX(n+1A)0..F
RX(n+D)0..F RX(n+1B)0..F
. .
. .
. .
RX(n+1A)0..F RX(n+36)0..F
V 2 V 2
2-way 4-way
RY(n+1)0.. RY(n+1)0..
F F
. .
. .
. .
RY(n+6)0.. RY(n+C)0.
F .F
RY(n+7)0.. RY(n+D)0.
F .F
. .
. .
. .
RY(n+C)0. RY(n+1A)0
.F ..F
V 2
8-way
RY(n+1)0..
F
.
.
.
RY(n+1A)0
..F
RY(n+1B)
0..F
.
.
.
RY(n+36)0
..F