Related Manuals for Pepperl+Fuchs IDENTControl IC-KP2 Series
Summary of Contents for Pepperl+Fuchs IDENTControl IC-KP2 Series
- Page 1 FACTORY AUTOMATION QUICK START GUIDE IC-KP2-* IDENTControl Compact control interfaces...
- Page 2 IC-KP2-* With regard to the supply of products, the current issue of the following document is applicable: The General Terms of Delivery for Products and Services of the Electrical Industry, published by the Central Association of the Electrical Industry (Zentralverband Elektrotechnik und Elektroindustrie (ZVEI) e.V.) in its most recent version as well as the supplementary clause: "Expanded reservation of proprietorship"...
-
Page 3: Table Of Contents
IC-KP2-* Contents 1 Introduction................. 4 Purpose of this quick start guide ..............4 Product documentation on the internet............4 2 Product Description ............5 Product family ....................5 Connection accessories................5 2.2.1 Connection cable for R/W heads and trigger sensors ......5 2.2.2 Cable connectors for the power supply ............6 2.2.3 Connection cable to the Ethernet interface..........6 2.2.4 Connection cable to the PROFIBUS DP interface ........7 2.2.5 Connection cable to the CC-Link interface ..........8... -
Page 4: Introduction
IC-KP2-* Introduction Introduction Purpose of this quick start guide This quick start guide contains basic instructions for operating the device. However, the manual takes priority over the quick start guide. Product documentation on the internet You can view all the relevant documentation and additional information on your product at http://www.pepperl-fuchs.com. -
Page 5: Product Description
IC-KP2-* Product Description Product Description Product family The brand name, IDENTControl, represents a complete identification system. The system consists of an IDENTControl Compact unit with serial interface, inductive R /W heads (125 kHz and 13.56 MHz), R / W heads with electromagnetic coupling (UHF with 868 MHz) and accompanying transponders in many different designs. -
Page 6: Cable Connectors For The Power Supply
IC-KP2-* Product Description 2.2.2 Cable connectors for the power supply Compatible M12 sockets with an open cable end for connecting the IDENTControl Compact to a power supply are available in different lengths. Figure 2.2 Accessories Model number Length 2 m (straight socket) V1-G-2M-PUR Length 5 m (straight socket) V1-G-5M-PUR... -
Page 7: Connection Cable To The Profibus Dp Interface
IC-KP2-* Product Description 2.2.4 Connection cable to the PROFIBUS DP interface The IDENTControl Compact has a B-coded M12 socket and is connected to the network using a suitable cable. Figure 2.4 Accessories Model number Terminator ICZ-TR-V15B T distributor ICZ-3T-V15B Y cable ICZ-3T-0.2M-PUR ABG-V15B-G Cable with terminator ICZ-2T/TR-0.2M-PUR ABG-V15B-G... -
Page 8: Connection Cable To The Cc-Link Interface
IC-KP2-* Product Description 2.2.5 Connection cable to the CC-Link interface The IDENTControl Compact has two M12 connectors. It is connected to the bus via standard CC-Link cable with M12 connectors. If you want to exchange the control unit without affecting the bus during operation (hot-plug capability), connect the control unit via a Y-cable to CC-Link IN. -
Page 9: Installation
IC-KP2-* Installation Installation Contact protection Our housings are manufactured using components made partly or completely from metal to improve noise immunity. Read head IDENTControl Compact Danger! Electric shock The metallic housing components are connected to ground to protect against dangerous voltages that may occur in the event of a fault in the SELV power supply! See chapter 3.5 Interface connections... -
Page 10: Profibus Interface
IC-KP2-* Installation Pin assignment of the M12 socket for RS 485 DGND 3.2.2 PROFIBUS interface Use the B-coded M12 socket and Y Cable ICZ-3T-0.2M-PUR ABG-V15B-G to connect the IDENTControl Compact unit to the PROFIBUS DP. RxD/TxD-N DGND RxD/TxD-P 3.2.3 Ethernet interface Use the D-coded M12 socket and the V1SD-G-5M-PUR-ABG-V45-G cable to connect the IDENTControl Compact unit to an Ethernet network. -
Page 11: Cc-Link Interface
IC-KP2-* Installation 3.2.4 CC-Link interface The control interface IC-KP2-2HB18-2V1 occupies 4 sations according to CC- Link. CC-Link IN: M12 connector, A-coded Pin assignment Signal Description Shield DB (white) Data B DG (yellow) Grounding DA (blue) Data A CC-Link OUT: M12 socket, A-coded Pin assignment Signal Description... -
Page 12: Ethercat Interface
IC-KP2-* Installation 3.2.5 EtherCAT interface For the connection of the IDENTControl Compact control interface to an EtherCAT network use the D-coded M12 socket and the cable V1SD-G-5M-PUR- ABG-V45-G. Power supply Connect the power supply using an M12 connector. A plug with the following pin assignment is located on the housing: + 24 V Compatible connecting cable see chapter 2.2.2... -
Page 13: R/W Heads And Trigger Sensors
IC-KP2-* Installation R/W heads and trigger sensors You can connect a maximum of two R/W heads (125 kHz or 13.56 MHz) or R/W heads with electromagnetic coupling (UHF with 868 MHz) to the IDENTControl Compact. On the two-channel unit, you can connect a trigger sensor to sockets 1 and 2 instead of a R/W head. -
Page 14: Commissioning
IC-KP2-* Commissioning Commissioning Connection This section contains information on how to commission the IDENTControl Compact. The example commissioning procedure described relates to the IDENTControl Compact with Ethernet interface. Caution! Uncontrollable triggered processes The plant where the device is installed may be damaged. Before commissioning, make sure that all processes run in a controlled manner. - Page 15 IC-KP2-* Commissioning Setting the IP address using the rotary switch 1. Select an IP address. Insert leading zeros so that all the numbers have three digits and then remove the periods. Example: Write the IP address 172.16.10.15 like this: 172016010015. 2.
-
Page 16: Technical Specifications
IC-KP2-* Technical specifications Technical specifications Dimensions 136.6 Figure 5.1 Dimensions: IC-KP2-1HB6-V15B ■ IC-KP2-1HB6-2V15B ■ IC-KP2-2HB6-V15B ■ IC-KP2-1HRX-2V1 ■ IC-KP2-2HRX-2V1 ■ IC-KP2-1HB17-2V1D ■ IC-KP2-2HB17-2V1D ■... - Page 17 IC-KP2-* Technical specifications 136.6 Figure 5.2 Dimensions: IC-KP2-2HB18-2V1 ■ IC-KP2-2HB21-2V1D ■...
- Page 18 Twinsburg, Ohio 44087 · USA Tel. +1 330 4253555 E-mail: sales@us.pepperl-fuchs.com Asia Pacific Headquarters Pepperl+Fuchs Pte Ltd. Company Registration No. 199003130E Singapore 139942 Tel. +65 67799091 E-mail: sales@sg.pepperl-fuchs.com www.pepperl-fuchs.com Subject to modifications Copyright PEPPERL+FUCHS • Printed in Germany 219360 DOCT-1804B_ENG 03/2012...