Epson Stylus Pro 5000 Service Manual page 171
Hide thumbs
Also See for Stylus Pro 5000:
- Service manual (780 pages) ,
- Reference manual (233 pages) ,
- Setup manual (100 pages)
Table of Contents
Advertisement
Stylus Pro 5000
Table 6-3. Lubrication Points (continued)
No.
Lubricating Points
5
The gearshaft on the right frame (shown in
Figure 6-2), from the frame to the slot for the
e-ring.
6
The gearshaft on the right frame (shown in
Figure 6-2).
7
The bent tip of the lifter gear train cover.
8
Contact point between the hopper lever and
the right frame.
9
A rib of the paper return cam
10
5 locations in the paper guide; see Figure
6-2.
11
2 contact points between the base
reinforcing plate and the rotary damper
mounting board.
12
The teeth of gear (11.5).
13
2 parts on the disengage cam; see Figure 6-
3.
14
The teeth of combination gear (14.4, 21.6).
15
The teeth of the larger half of combination
gear (12, 15)
16
The shaft attached to the right frame; See
Figure 6-3.
17
The teeth of gear (25.8).
18
A shaft attached to the left frame; see Figure
6-3.
19
The teeth of the larger half of combination
gear (12, 26).
No.
Type/Amount
20
G-26 (=25 mm)
21
22
G-26 (=2 mm)
23
G-26 (=2 mm)
G-26 (=2 mm)
24
G-26 (=2 mm)
25
G-26 (=5 mm)
26
G-26 (=1 mm)
27
G-26 (on 1/3 of
28
the gear teeth)
29
G-26 (=5 mm)
30
G-26 (on 1/3 of
31
the gear teeth)
G-26 (on 1/3 of
32
the gear teeth)
G-26 (=10 mm)
33
G-26 (=1 mm,
on 1/3 of the
34
gear teeth)
G-26 (=10 mm)
G-26 (=1 mm,
on 1/3 of the
gear teeth)
Table 6-3. Lubrication Points (continued)
Lubricating Points
12 points on the front paper guide.
4 points on the paper eject grounding plate.
2 contact areas; between the paper eject
rollers and the paper eject grounding plate.
2 contact areas; between the rear paper
eject rollers and the paper eject grounding
plate.
The section of gear (27) shown in Figure
6-4.
2 points on the release lever camshaft.
Note: Do not lubricate the roller surface.
Oil pad. Put oil in the oil supply hole on the
carriage.
Note: Only lubricate the oil pad.
A hole in the left frame.
The right roller release lever.
Pin on the right frame.
The slot at the end of the shaft shown in
Figure 6-5.
The U-shaped cutouts on the left and right
paper guides.
The carriage shaft.
Note: Do not lubricate the carriage support
shaft.
Lubricate the holes in the end of the shaft
through combination gear (29.6, 29.6).
The shaft ends shown in Figure 6-5.
Chapter 6 Maintenance
Type/Amount
G-26 (=2 mm)
G-20 (=2 mm)
G-20 (=2 mm)
G-20 (=2 mm)
G-26 (on 1/4 of
the gear teeth)
G-26 (=2 mm)
0-8 (0.8 cc)
G-26 (=3 mm)
G-26 (=1 mm)
G-26 (=3 mm)
G-26 (=2 mm)
G-26 (=5 mm,
top and bottom)
0-8 (Wipe with
an oil-moistened
cloth)
G-26 (=5 mm)
G-26 (=5 mm)
6-4
Advertisement
Table of Contents
