Danfoss VLT AutomationDrive FC 300 Programming Manual page 185

Parameter Lists
Par. No. # Parameter description
Process PID Gain Scale at Min.
7-43 Ref.
Process PID Gain Scale at Max.
7-44 Ref.
7-45 Process PID Feed Fwd Resource
Process PID Feed Fwd Normal/
7-46 Inv. Ctrl.
7-48 PCD Feed Forward
Process PID Output Normal/ Inv.
7-49 Ctrl.
7-5* Adv. Process PID II
7-50 Process PID Extended PID
7-51 Process PID Feed Fwd Gain
7-52 Process PID Feed Fwd Ramp up
Process PID Feed Fwd Ramp
7-53 down
7-56 Process PID Ref. Filter Time
7-57 Process PID Fb. Filter Time
4.1.11 8-** Comm. and Options
Par. No. # Parameter description
8-0* General Settings
8-01 Control Site
8-02 Control Word Source
8-03 Control Word Timeout Time
8-04 Control Word Timeout Function
8-05 End-of-Timeout Function
8-06 Reset Control Word Timeout
8-07 Diagnosis Trigger
8-08 Readout Filtering
8-1* Ctrl. Word Settings
8-10 Control Word Profile
8-13 Configurable Status Word STW
8-14 Configurable Control Word CTW
8-19 Product Code
8-3* FC Port Settings
8-30 Protocol
8-31 Address
8-32 FC Port Baud Rate
8-33 Parity / Stop Bits
8-34 Estimated cycle time
8-35 Minimum Response Delay
8-36 Max Response Delay
8-37 Max Inter-Char Delay
8-4* FC MC protocol set
8-40 Telegram Selection
8-41 Parameters for Signals
®
VLT AutomationDrive Programming Guide
Default value
100 %
100 %
[0] No function
[0] Normal
0 N/A
[0] Normal
[1] Enabled
1 N/A
0.01 s
0.01 s
0.001 s
0.001 s
Default value
[0] Digital and ctrl.word All set-ups
ExpressionLimit All set-ups
1 s
ExpressionLimit
[1] Resume set-up
[0] Do not reset All set-ups
[0] Disable
ExpressionLimit All set-ups
[0] FC profile All set-ups
ExpressionLimit All set-ups
[1] Profile default All set-ups
ExpressionLimit
[0] FC
1 N/A
ExpressionLimit
[0] Even Parity, 1 Stop
Bit
0 ms
10 ms
ExpressionLimit
ExpressionLimit
[1] Standard telegram 1
0 All set-ups
®
MG33MG02 - VLT is a registered Danfoss trademark
4-set-up FC 302 Change
only during
operation
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups x TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
4-set-up FC 302 Change
only during
operation
TRUE
TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
TRUE
2 set-ups TRUE
TRUE
TRUE
TRUE
TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
2 set-ups TRUE
1 set-up TRUE
1 set-up TRUE
1 set-up TRUE
2 set-ups TRUE
FALSE
Conver- Type
sion index
0 Int16
0 Int16
- Uint8
4
- Uint8
0 Uint16
- Uint8
- Uint8
-2 Uint16
-2 Uint32
-2 Uint32
-3 Uint16
-3 Uint16
Conver- Type
sion index
- Uint8
- Uint8
-1 Uint32
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
0 Uint32
- Uint8
0 Uint8
- Uint8
- Uint8
-3 Uint32
-3 Uint16
-3 Uint16
-5 Uint16
- Uint8
- Uint16
183
4