Danfoss VLT AutomationDrive FC 300 Programming Manual page 120

Parameter Descriptions
8-54 Reversing Select
Option:
[1] Bus
[2] Logic AND
3 3
[3] Logic OR
8-55 Set-up Select
Option:
[0] Digital
input
[1] Bus
[2] Logic AND
[3] Logic OR
8-56 Preset Reference Select
Option:
[0] Digital
input
[1] Bus
[2] Logic AND
[3] Logic OR
8-57 Profidrive OFF2 Select
Select control of the frequency converter OFF2 selection via the
terminals (digital input) and/or via the fieldbus. This parameter is
active only when 8-01 Control Site is set to [0] Digital and ctrl.
word and 8-10 Control Word Profile is set to [1] Profidrive profile.
Option:
[0]
[1]
[2]
118
VLT
Function:
Activates the Reverse command via the serial
communication port or fieldbus option.
Activates the Reverse command via the
fieldbus/serial communication port, AND
additionally via one of the digital inputs.
Activates the Reverse command via the
fieldbus/serial communication port OR via one
of the digital inputs.
Function:
Select control of the frequency converter set-up
selection via the terminals (digital input) and/or
via the fieldbus.
Activates the set-up selection via a digital input.
Activates the set-up selection via the serial
communication port or fieldbus option.
Activates the set-up selection via the fieldbus/
serial communication port, AND additionally via
one of the digital inputs.
Activate the set-up selection via the fieldbus/
serial communication port OR via one of the
digital inputs.
Function:
Select control of the frequency converter Preset
Reference selection via the terminals (digital
input) and/or via the fieldbus.
Activates Preset Reference selection via a digital
input.
Activates Preset Reference selection via the
serial communication port or fieldbus option.
Activates Preset Reference selection via the
fieldbus/serial communication port, AND
additionally via one of the digital inputs.
Activates the Preset Reference selection via the
fieldbus/serial communication port OR via one
of the digital inputs.
Function:
Digital input
Bus
Logic AND
MG33MG02 - VLT
®
AutomationDrive Programming Guide
8-57 Profidrive OFF2 Select
Select control of the frequency converter OFF2 selection via the
terminals (digital input) and/or via the fieldbus. This parameter is
active only when 8-01 Control Site is set to [0] Digital and ctrl.
word and 8-10 Control Word Profile is set to [1] Profidrive profile.
Option:
[3]
8-58 Profidrive OFF3 Select
Select control of the frequency converter OFF3 selection via the
terminals (digital input) and/or via the fieldbus. This parameter is
active only when 8-01 Control Site is set to [0] Digital and ctrl.
word and 8-10 Control Word Profile is set to [1] Profidrive profile.
Option:
[0]
[1]
[2]
[3]
3.10.6 8-8* FC Port Diagnostics
These parameters are used for monitoring the Bus
communication via the FC Port.
8-80 Bus Message Count
Range:
0 [0 - 0 ] This parameter shows the number of valid
*
8-81 Bus Error Count
Range:
0 [0 - 0 ] This parameter shows the number of telegrams
*
8-82 Slave Messages Rcvd
Range:
0 [0 - 0 ] This parameter shows the number of valid
*
8-83 Slave Error Count
Range:
0 [0 - 0 ] This parameter shows the number of error
*
®
is a registered Danfoss trademark
Function:
Logic OR
Function:
Digital input
Bus
Logic AND
Logic OR
Function:
telegrams detected on the bus.
Function:
with faults (e.g. CRC fault), detected on the bus.
Function:
telegrams addressed to the slave, sent by the
frequency converter.
Function:
telegrams, which could not be executed by the
frequency converter.