Operation Mode; Start/Stop - ABB ACS880 Firmware Manual

94 Parameters
No. Name/Value
116.81 AO1 source max
116.82 AO1 out at AO1 src
min
116.83 AO1 out at AO1 src
max
116.86 AO2 actual value
116.87 AO2 source
116.88 AO2 force data
116.89 AO2 filter time
116.90 AO2 source min
116.91 AO2 source max
116.92 AO2 out at AO2 src
min
116.93 AO2 out at AO2 src
max
119

119 Operation mode

119.17 Local control disable
No
Yes
120

120 Start/stop

120.01 Ext1 commands
Not sel
In1 Start
Description
(Visible when 116.01 Module 3 type
See parameter 114.81 AO1 source
(Visible when 116.01 Module 3 type
See parameter 114.82 AO1 out at AO1 src
(Visible when 116.01 Module 3 type
See parameter 114.83 AO1 out at AO1 src
(Visible when 116.01 Module 3 type
See parameter 114.86 AO2 actual
(Visible when 116.01 Module 3 type
See parameter 114.87 AO2
(Visible when 116.01 Module 3 type
See parameter 114.88 AO2 force
(Visible when 116.01 Module 3 type
See parameter 114.89 AO2 filter
(Visible when 116.01 Module 3 type
See parameter 114.90 AO2 source
(Visible when 116.01 Module 3 type
See parameter 114.91 AO2 source
(Visible when 116.01 Module 3 type
See parameter 114.92 AO2 out at AO2 src
(Visible when 116.01 Module 3 type
See parameter 114.93 AO2 out at AO2 src
Selection of external control location sources.
See section Control locations for start/stop
Enables/disables (or selects a source that enables/disables)
local control.
WARNING! Before disabling local control, ensure
that the control panel is not needed for stopping
the DC/DC converter unit.
Local control enabled.
Local control disabled.
Start/stop, run/enable and start enable signal source
selection.
See section Run enable, Start/stop and Start enable control
on page 32.
Selects the source of start and stop commands for external
control location 1 (EXT1).
Note: This parameter cannot be changed while the
converter is running.
No start or stop command sources selected.
The source of the start and stop commands is selected by
parameter 120.03 Ext1 in1. The state transitions of the
source bit are interpreted as follows:
State of source
(120.03)
0 - > 1
1 - > 0
= FIO-11 or FAIO-01)
max.
= FIO-11 or FAIO-01)
min.
= FIO-11 or FAIO-01)
max.
= FAIO-01)
value.
= FAIO-01)
source.
= FAIO-01)
data.
= FAIO-01)
time.
= FAIO-01)
min.
= FAIO-01)
max.
= FAIO-01)
min.
= FAIO-01)
max.
on page 26.
Command
Start
Stop
Def/FbEq16
1500.0
0.000 mA
20.000 mA
-
Zero
0.000 mA
0.100 s
0.0
100.0
0.000 mA
10.000 mA
No
0
1
In1 Start
0
1