Siemens SINAMICS G120 Original Instructions Manual page 178
Sinamics g120 inverter with cu230p-2 control
units
Hide thumbs
Also See for SINAMICS G120:
- List manual (1256 pages) ,
- Manual (732 pages) ,
- Operating instructions manual (550 pages)
Table of Contents
Advertisement
Configuring the fieldbus
7.6 Communication via RS485
Instance
Object name
ID
BV9
AT MAX
FREQ
BV10
DRIVE
READY
BV15
RUN COM
ACT
BV16
HIB MOD
ACT
BV17
ESM MOD
BV20
RUN / STOP
CMD
BV21
FWD / REV
CMD
BV22
FAULT
RESET
BV24
CDS
BV26
RUN ENA
CMD
BV27
OFF2
BV28
OFF3
BV50
ENABLE PID Enable technology controller
BV51
ENABLE
PID 0
BV52
ENABLE
PID 1
BV53
ENABLE
PID 2
BV90
LOCAL
LOCK
BV93
CTL
OVERRIDE
CMD
Analog Input Objects
Instance
Object name
ID
AI0
ANALOG INPUT 0
AI1
ANALOG INPUT 1
AI2
ANALOG INPUT 2
AI3
ANALOG INPUT 3
178
Description
Maximum speed reached
Inverter ready
ACT indicates the status of the
ON command, regardless of the
source
ACT means that the inverter is
operating in energy-saving mode.
ACT means that the inverter is
operating in the essential service
mode
ON command for the inverter
(when controlling via BACnet)
Reverse direction of rotation
(when controlling via BACnet)
Acknowledge fault (when
controlling via BACnet)
Local / Remote
Enable inverter operation
OFF2 status
OFF3 status
Note:
BV28 sets the r0054.4, r0054.5,
and r0054.6 bits
Enable technology 0 controller
Enable technology 1 controller
Enable technology 2 controller
Use MANUAL (operator panel) to
lock inverter control
Inverter control using BACnet
override control
Description
AI0 input signal
AI1 input signal
AI2 input signal
AI3 input signal
Possible values
Text
active
YES / NO
YES
YES / NO
YES
YES / NO
0
ON/OFF
0
ON/OFF
0
RUN / STOP
0
REV / FWD
0
RESET / NO
0
Local / Remote
YES
ENABLED DISABLED
RUN / STOP
0
RUN / STOP
0
ENABLED /
ENABLED DISABLED
DISABLED
ENABLED /
ENABLED DISABLED
DISABLED
ENABLED /
ENABLED DISABLED
DISABLED
ENABLED /
ENABLED DISABLED
DISABLED
LOCK
ON/OFF
0
Unit
Range
V/mA
inverter-dependent
V/mA
inverter-dependent
V/mA
inverter-dependent
V/mA
inverter-dependent
Operating Instructions, 11/2013, FW V4.6.6, A5E02430659B AG
Text
Access
Parameter
inactive
type
NO
R
r0052.10
NO
R
r0052.1
1
R
r2032[0]
1
R
r2399[1]
1
R
r3889[0]
1
C
r0054.0
1
C
r0054.11
1
C
r0054.7
NO
C
r0054.15
C
r0054.3
1
C
r0054.1
1
C
r0054.2
C
p2200
C
p11000
C
p11100
C
p11200
UNLOCK C
p0806
1
C
r0054.10
Access
Parameter
type
R
r0752[0]
R
r0752[1]
R
r0752[2]
R
r0752[3]
Inverter with CU230P-2 Control Units
Advertisement
Table of Contents
