Mitsubishi Electric MELSEC iQ-R Series Programming Manual page 369

Variable name Description
LLAG_T1 First Order Lag: Delay Time (Sec)
PVCMP_EN PV Compensation Execution condition
PVCMP_MODE PV Compensation Mode
PV Compensation Execution condition
PVDCMP_EN
PID2H_MTD Derivative Gain
PID2H_DVLS Large Deviation Alarm Hysteresis
PID2H_PN Reverse Action/Direct Action
PID2H_SVPTN_B0 Setting Value (SV) Used
PID2H_PVTRK_EN PV Tracking Execution condition
PID2H_ISTP Integration Stop Signal
PID2H_DSTP Derivation Stop Signal
PID2H_LMT_ISTP Stop Integration, when MV variation rate limiter
alarm occurred
PID2H_SVLMT_EN SV High/Low Limiter
MV Compensation Execution condition
MVDCMP_EN
MV Compensation Mode
MVDCMP_MODE
MV Gain Correction Execution condition
MVDGAINCMP_EN
OUT3_NMAX Output Conversion High Limit
OUT3_NMIN Output Conversion Low Limit
OUT3_MVCMP_EN MV Compensation Execution condition
OUT3_MVCMP_MOD MV Compensation Mode
E
OUT3_PREMV_EN Preset MV Execution condition
OUT3_PREMV_V Preset MV Value (Unit: %)
OUT3_MVHLD_EN MV Hold Execution condition
OUT3_MVTRK_EN MV Tracking Execution condition
OUT3_STP_OTYPE Output when loop or tag is stopped
OUT3_SEA_OTYPE MV Output Selection when SEA is occurred
OUT3_ARW_EX_EN MV Value Instantaneous Pullback
OUT3_MVPH MV Internal Operation High Limit Value (Unit: %)
OUT3_MVPL MV Internal Operation Low Limit Value (Unit: %)
OUT3_MVREV_EN MV Reverse Execution condition
OUT3_FOTS_EN Tight Shut/Full Open Execution condition
OUT3_MVFO Output Value for Full Open (Unit: %)
OUT3_MVTS Output Value for Tight Shut (Unit: %)
12.10 2-degree-of-freedom Advanced PID Control (Disable Tracking for primary loop) (M+M_2PIDH_)
Recommended range Initial
value
0 to 999999[s] 1.0
TRUE: Execute FALSE
FALSE: Stop
0: Addition 0
1: Replacement
TRUE: Execute FALSE
FALSE: Stop
0 to 9999 8.0
0 to 100 2.0
0: Reverse action 0
1: Direct action
TRUE: Not used TRUE
FALSE: Used
TRUE: Execute FALSE
FALSE: Stop
TRUE: Execute FALSE
FALSE: Stop
TRUE: Execute FALSE
FALSE: Stop
TRUE: Stop FALSE
FALSE: Not stop
TRUE: Execute FALSE
FALSE: Not execute
TRUE: Execute FALSE
FALSE: Stop
0: Addition 0
1: Replacement
TRUE: Execute FALSE
FALSE: Stop
-999999 to 999999 100.0
-999999 to 999999 0.0
TRUE: Execute FALSE
FALSE: Stop
0: Addition 0
1: Replacement
TRUE: Execute FALSE
FALSE: Stop
0 to 100[%] 0.0
TRUE: Execute FALSE
FALSE: Stop
TRUE: Execute FALSE
FALSE: Stop
0: Hold 0
1: Preset value
0: Hold 0
1: Preset MV output
2: Neither hold nor preset MV
output is performed.
TRUE: Execute FALSE
FALSE: Not execute
MH to 999999[%] 100.0
-999999 to ML[%] 0.0
TRUE: Execute FALSE
FALSE: Stop
TRUE: Execute FALSE
FALSE: Stop
100 to 125[%] 112.5
-25 to 0[%] -16.82
Set by Data type
User REAL
User BOOL
User INT
User BOOL
User REAL
User REAL
User INT
User BOOL
User BOOL
User BOOL
User BOOL
User BOOL
User BOOL
User BOOL
User INT
User BOOL
User REAL
User REAL
User BOOL
User INT
User BOOL
User REAL
User BOOL
User BOOL
User INT
User INT
User BOOL
User REAL
User REAL
User BOOL
User BOOL
User REAL
User REAL
12 LOOP TAG
367
12