YASKAWA A1000 HHP Programming Manual page 352

Index
Motor 2 Rated Slip ...............................................................81
Motor 2 Slip Compensation Gain...............................................50
Motor 2 Slip Compensation Limit..............................................51
Motor 2 Slip Compensation Primary Delay Time............................50
Motor 2 Slip Compensation Selection during Regeneration ................51
Motor 2 Torque Compensation Gain...........................................52
Motor Base Frequency ................................................... 169, 296
Motor Base Speed ........................................................ 169, 296
Motor Data Error................................................................ 218
Motor d-Axis Current at Previous Fault ..................................... 301
Motor Direction at Power Up when Using Operator................. 164, 293
Motor Direction Error .......................................................... 219
Motor Does Not Rotate ........................................................ 227
Motor Excitation Current (ld) ................................................. 305
Motor Hunting and Oscillation Control Parameters ....................... 177
Motor Iron-Core Saturation Coefficient ..................................... 217
Motor Iron-Core Saturation Coefficient 1 .....................................78
Motor Iron-Core Saturation Coefficient 2 .....................................78
Motor Iron Loss ........................................................... 170, 297
Motor Iron Loss for Torque Compensation ...................................79
Motor Leakage Inductance ......................................................78
Motor Line-to-Line Resistance .................................................78
Motor Mechanical Loss ..........................................................78
Motor No-Load Current....................................................77, 169
Motor Overheat ................................................................. 208
Motor Overheat (NTC Input) ........................................... 194, 209
Motor Overheat Alarm (PTC Input).......................................... 194
Motor Overheat Alarm Operation Selection .......................... 131, 282
Motor Overheat Fault (PTC Input) ........................................... 194
Motor Overheat Fault Operation Selection............................ 131, 282
Motor Overload ................................................................. 195
Motor Overload Estimate (oL1) .............................................. 303
Motor Overload Protection Selection .................................. 113, 282
Motor Overload Protection Time ....................................... 130, 282
Motor Performance Fine-Tuning ............................................. 176
Motor Protection ................................................................ 128
Motor Protection Using a PTC Thermistor.................................. 120
Motor PTC Characteristics .................................................... 131
Motor q-Axis Current at Previous Fault ..................................... 301
Motor Rated Current .................................................77, 169, 296
Motor Rated Power ...................................................79, 168, 296
Motor Rated Slip............................................................77, 169
Motor Rated Voltage ..................................................... 168, 296
Motor Rotates in One Direction Only........................................ 228
Motor Secondary Current (Iq) ................................................ 305
Motor Selection ................................................................. 100
Motor Selection 1/2............................................................. 296
Motor Speed ..................................................................... 298
Motor Speed at Previous Fault ................................................ 300
Motor Speed Error 2............................................................ 220
Motor Speed Fault .............................................................. 219
Motor Switch during Run...................................................... 210
Motor Temperature (NTC ..................................................... 304
Motor Temperature Input Filter Time.................................. 132, 282
Multi-Function Analog Input Selection Error............................... 214
Multi-Function Analog Input Terminal Settings ........................... 115
Multi-Function Analog Outputs ................................................53
Multi-Function Analog Output Terminal AM Bias ........................ 121
Multi-Function Analog Output Terminal AM Gain........................ 121
Multi-Function Analog Output Terminal AM Monitor Selection........ 121
352
Multi-Function Analog Output Terminal AM Signal Level Selection .. 122
Multi-Function Analog Output Terminal FM Bias......................... 121
Multi-Function Analog Output Terminal FM Gain ........................ 121
Multi-Function Analog Output Terminal FM Monitor Selection ........ 121
Multi-Function Analog Output Terminal FM Signal Level Selection... 122
Multi-Function Digital Input Terminal Settings ..............................95
Multi-Function Digital Output Terminal Settings .......................... 105
Multi-Function Input Selection Error ........................................ 213
Multi-Step Speed Selection......................................................19
N
n1-02.............................................................................. 176
n2-01.............................................................................. 176
n2-02.............................................................................. 176
n2-03.............................................................................. 177
ND ..................................................................................58
ndAT.............................................................................. 223
NetRef/ComRef Function Selection............................................90
Network Termination .......................................................... 316
Noise From the Drive or Motor Cables When the Drive is Powered On 231
No-Load Current Alarm ....................................................... 218
No-Load Current Error......................................................... 218
Normal Duty.......................................................................58
nSE ............................................................................... 190
Number of Auto Restart Attempts...................................... 147, 286
Number of Motor Poles ..............................................78, 169, 296
Number of Run Commands ................................................... 302
Number of Run Commands Counter Initialization......................... 166
Number of Speed Search Restarts ..............................................32
O
o2-01.............................................................................. 227
oC ................................................................................. 190
oFA00 ............................................................................ 191
oFA01 ............................................................................ 191
oFA03 to oFA06 ................................................................ 192
oFA10 ............................................................................ 192
oFA11 ............................................................................ 192
oFA12 to oFA17 ................................................................ 192
oFA30 to oFA43 ................................................................ 192
oFb00 ............................................................................. 192
oFb01 ............................................................................. 192
oFb02 ............................................................................. 192
oFb03 to oFb11 ................................................................. 192
oFb12 to oFb17 ................................................................. 192
oFC00 ............................................................................ 192
oFC01 ............................................................................ 193
oFC02 ............................................................................ 193
oFC03 to oFC11 ................................................................ 193
oFC12 to oFC17 ................................................................ 193
Offset Frequency................................................................ 306
oH ........................................................................... 193, 208
oH1 ............................................................................... 193
oH2 ............................................................................... 208
oH3 ......................................................................... 194, 208
oH4 ............................................................................... 194
oH5 ......................................................................... 194, 209
oH6 ............................................................................... 194
oH Alarm Location Monitor .................................................. 304
oL1................................................................................ 195
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual