YASKAWA A1000 HHP Programming Manual page 350

Index
Fault Reset Methods............................................................ 179
Fault Reset Operation Selection ........................................ 148, 286
Fault Restart ..................................................................... 113
Faults ............................................................................. 179
Fault SlaveLocation Monitor.................................................. 301
Fault Trace................................................................. 171, 224
FbH ......................................................................... 189, 206
FbL ......................................................................... 189, 206
Field Forcing ......................................................................72
Field Forcing Limit ...............................................................73
Field Forcing Selection ..........................................................72
Field Weakening ..................................................................72
Field Weakening Frequency Limit .............................................72
Field Weakening Level ..........................................................72
Fine-Tuning Open Loop Vector Control .................................... 176
Fine-Tuning V/f Control and V/f Control with PG ........................ 176
FJOG/RJOG Operation ..........................................................99
Forward/Reverse Run Command Input Error............................... 205
Forward Regenerative Torque Limit ................................... 151, 287
Forward Torque Limit.................................................... 151, 287
Frequency Detection 1 Time Chart........................................... 108
Frequency Detection 2 Time Chart........................................... 108
Frequency Detection 3 Example with a Positive L3-04 Value ........... 111
Frequency Detection 4 Example with Positive L3-04 Value ............. 112
Frequency Reduction Rate during Overheat Pre-Alarm............. 153, 289
Frequency Reference .......................................................59, 298
Frequency Reference at Previous Fault ...................................... 300
Frequency Reference at Reference Loss............................... 146, 285
Frequency Reference Bias .......................................................65
Frequency Reference Bias (Up/Down 2) .................................... 306
Frequency Reference Bias Accel/Decel .......................................66
Frequency Reference Bias Lower Limit .......................................65
Frequency Reference Bias Operation Mode Selection ......................66
Frequency Reference Bias Step.................................................65
Frequency Reference Bias Upper Limit .......................................65
Frequency Reference from MEMOBUS/Modbus Comm. ................ 303
Frequency Reference Hold Function Selection ...............................63
Frequency Reference Loss Detection Selection ...................... 109, 285
Frequency Reference Lower Limit .............................................61
Frequency Reference Monitor Content During PID .........................42
Frequency Reference Selection ............................................... 240
Frequency Reference Selection 1.........................................18, 227
Frequency Reference Selection 2...............................................24
Frequency Reference Setting / Decimal Display ........................... 292
Frequency Reference Setting and User-Set Display ....................... 292
Frequency Reference Setting Hierarchy .......................................59
Frequency Reference Setting Method Selection...................... 163, 293
Frequency Reference Source Selection ...................................... 303
Frequency Reference Upper Limit .............................................61
Function Code................................................................... 324
Functions for Terminals S1 to S8...............................................95
Fuse is Open ..................................................................... 198
G
Gate Drive Board Undervoltage .............................................. 201
GF................................................................................. 189
Ground Fault .................................................................... 189
H
H1 Multi-Function Digital Input Selections................................. 269
350
H3-02 ............................................................................. 230
H3-13 ............................................................................. 177
H3 Multi-Function Analog Input Settings................................... 277
Hbb ............................................................................... 206
HbbF.............................................................................. 207
HCA .............................................................................. 207
HD ..................................................................................58
Heatsink Cooling Fan Off-Delay Time ...................................... 155
Heatsink Cooling Fan Operation Delay Time .............................. 288
Heatsink Cooling Fan Operation Selection............................ 154, 288
Heatsink Overheat ........................................................ 193, 208
Heatsink Overheat Warning ................................................... 208
Heatsink Temperature.......................................................... 302
Heavy Duty ........................................................................58
High Current Alarm Selection ................................................ 156
High Slip Braking .............................................................. 159
High Slip Suppression Current Level ........................................ 160
High-Slip Suppression Current Level........................................ 291
Hunting Prevention ............................................................. 158
Hunting Prevention Gain ...................................................... 176
Hunting Prevention Gain Setting ....................................... 158, 290
Hunting Prevention Gain while in Reverse ........................... 158, 290
Hunting Prevention Selection ........................................... 158, 290
Hunting Prevention Time Constant .................................... 158, 290
HVAC Fan Application ..........................................................15
Hybrid IC Failure ............................................................... 186
I
iFEr ............................................................................... 222
IGBT Maintenance ............................................................. 302
IGBT Maintenance Setting .............................................. 166, 293
IGBT Maintenance Time (50%) .............................................. 208
IGBT Maintenance Time (90%) ............................................. 211
Induction Voltage Error........................................................ 220
Initialization .......................................................................10
Initialization Required ......................................................... 214
Initialize Parameters..............................................................11
Input Phase Loss ................................................................ 197
Input Phase Loss Protection Selection ................................. 153, 288
Input Pulse Monitor ............................................................ 300
Input Terminal Status .......................................................... 298
Input Terminal Status at Previous Fault ..................................... 301
Input Voltage Setting.............................................................74
Inrush Prevention Relay Fault ................................................ 201
Inrush Prevention Relay Maintenance Setting .............................. 293
Integral Limit Setting.............................................................37
Integral Operation during Accel/Decel ........................................56
Integral Operation during Accel/Decel for Motor 2..........................57
Integral Time Setting (I) .........................................................37
J
Jog Frequency Reference ........................................................59
Jump Frequency................................................................. 177
Jump Frequency Width ..........................................................62
K
KEB Acceleration Time ................................................. 140, 283
KEB Detection Time ........................................................... 140
KEB Function Related Adjustments ......................................... 139
KEB Operation Using a KEB Input .......................................... 136
KEB Operation Using L2-02, Without KEB Input......................... 136
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual