YASKAWA A1000 HHP Programming Manual page 278

A.9 H Parameters: Multi-Function Terminals
H3-oo
Function
Setting
6 DC Injection Braking current
Overtorque/undertorque
7
detection level
8 Stall Prevention level during run
9 Output frequency lower limit level
B PID feedback
C PID setpoint
D Frequency bias
E Motor temperature (PTC input)
F Through mode
10 Forward torque limit
11 Reverse torque limit
12 Regenerative torque limit
13 Torque reference/Torque limit
14 Torque compensation
15 General torque limit
16 Differential PID feedback
17 Motor Thermistor (NTC)
1F Through mode
DriveWorksEZ
30 to 32
analog input 1 to 3
278
H3 Multi-Function Analog Input Settings
V/f V/f V/f w PG V/f w PG OLV OLV
OLV/PM AOLV/PM CLV/PM
10 V = Drive rated current
All Modes
10 V = Drive rated current (V/f, V/f w PG)
10 V = Motor rated torque (OLV, CLV, OLV/PM, AOLV/PM, CLV/PM)
V/f V/f V/f w PG V/f w PG OLV
OLV/PM AOLV/PM CLV/PM
10 V = Drive rated current
All Modes
10 V = E1-04 (maximum output frequency)
All Modes
10 V = 100%
All Modes
10 V = 100%
All Modes
10 V = E1-04 (maximum output frequency)
All Modes
10 V = 100%
All Modes
Set this value when using the terminal in the pass-through mode.
V/f V/f V/f w PG V/f w PG OLV OLV OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
10 V = Motor rated torque
V/f V/f V/f w PG V/f w PG OLV OLV OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
10 V = Motor rated torque
V/f V/f V/f w PG V/f w PG OLV OLV OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
10 V = Motor rated torque
V/f V/f V/f w PG V/f w PG OLV OLV OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
10 V = Motor rated torque
V/f V/f V/f w PG V/f w PG OLV OLV OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
10 V = Motor rated torque
V/f V/f V/f w PG V/f w PG OLV OLV OLV OLV
OLV/PM OLV/PM AOLV/PM AOLV/PM AOLV/PM AOLV/PM CLV/PM CLV/PM CLV/PM CLV/PM
10 V = Motor rated torque
All Modes
10 V = 100%
All Modes
10 V = -9 °C
0 V = 234 °C
Note:
This function is only available in models CIMR-Ao4A0930, 4A1200 and
A1000 HHP.
All Modes
Set this value when using the terminal in the pass-through mode.
All Modes
Output is determined by the function selected using DWEZ.
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual
Description
CLV
CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
CLV CLV CLV CLV
Page
119
119
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120