YASKAWA A1000 HHP Programming Manual page 353

oL2................................................................................ 195
oL2 Characteristics Selection at Low Speeds......................... 155, 288
oL3.......................................................................... 196, 209
oL4.......................................................................... 196, 209
oL5.......................................................................... 196, 209
oPE ............................................................................... 213
oPE01 ............................................................................ 213
oPE02 ............................................................................ 213
oPE03 ............................................................................ 213
oPE04 ............................................................................ 214
oPE05 ............................................................................ 214
oPE06 ............................................................................ 214
oPE07 ............................................................................ 214
oPE08 ............................................................................ 215
oPE09 ............................................................................ 215
oPE10 ............................................................................ 215
oPE13 ............................................................................ 216
oPE15 ............................................................................ 216
oPE16 ............................................................................ 216
oPE18 ............................................................................ 216
oPE Fault Parameter............................................................ 299
Open Loop Vector Control .................................................... 177
Open Loop Vector Control Mode Tuning ................................... 176
Open Loop Vector Control Mode Tuning Parameters ..................... 176
Operation Errors .......................................................... 179, 182
Operation Selection at Overspeed (oS) ........................................84
Operation Selection at PG Open Circuit (PGo)...............................84
Operation Selection when Digital Operator is Disconnected ....... 164, 293
Operation Status Monitors..................................................... 171
Operator Programming Errors ................................................ 213
Operator Related Settings...................................................... 161
oPr ................................................................................ 196
Option card connection error (CN5-A) ...................................... 192
Option Card Connection Error at Option Port CN5-A..................... 191
Option Card Connection Error at Option Port CN5-C..................... 192
Option card error occurred at option port CN5-A .......................... 192
Option card error occurred at option port CN5-B .......................... 192
Option card error occurred at option port CN5-C .......................... 193
Option Card External Fault.............................................. 188, 205
Option Card Fault at Option Port CN5-A ................................... 191
Option Card Fault at Option Port CN5-B.................................... 192
Option Card Fault at Option Port CN5-C.................................... 193
Option Communication Error ........................................... 184, 203
Option Frequency Reference .................................................. 303
Option Settings....................................................................84
oS ........................................................................... 196, 209
Oscillation or Hunting.......................................................... 231
Output Current .................................................................. 298
Output Current 1 During Speed Search........................................32
Output Current at Previous Fault ............................................. 300
Output Current Imbalance ..................................................... 190
Output Frequency............................................................... 298
Output Frequency after Soft Start ............................................ 299
Output Frequency at Previous Fault.......................................... 300
Output Frequency Reduction During Overheat Alarm .................... 153
Output Ground Fault Detection Selection ............................. 154, 288
Output of speed control (ASR) (for Simple V/f PG)....................... 305
Output Phase Loss .............................................................. 189
Output Phase Loss Protection ................................................. 288
Output Phase Loss Protection Selection ..................................... 154
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual
Output Power.................................................................... 298
Output Power at Previous Fault............................................... 301
Output Short Circuit or IGBT Fault .......................................... 199
Output Terminal Status ........................................................ 299
Output Terminal Status at Previous Fault ................................... 301
Output Voltage at Previous Fault ............................................. 300
Output Voltage Detection Fault......................................... 201, 212
Output Voltage Limit Operation Selection ....................................50
Output Voltage Reference ..................................................... 298
Output Voltage Reference (Vd)............................................... 305
Output Voltage Reference (Vq)............................................... 305
ov............................................................................ 196, 210
OV Alarm Location Monitor.................................................. 304
Overcurrent ...................................................................... 190
Overexcitation Deceleration................................................... 143
Overexcitation Deceleration Gain ...................................... 160, 290
Overexcitation Operation Selection .................................... 160, 291
Overheat 1 (Heatsink Overheat) .............................................. 193
Overheat Alarm Level.................................................... 113, 288
Overheat Pre-Alarm Operation Selection ............................. 114, 288
Overspeed.................................................................. 196, 209
Overspeed Detection Delay Time ..............................................84
Overspeed Detection Level......................................................84
Overtorque 1..................................................................... 209
Overtorque 2..................................................................... 209
Overtorque Detection 1 ........................................................ 196
Overtorque Detection 2 ........................................................ 196
Overtorque Detection Operation.............................................. 148
Overvoltage...................................................................... 196
Overvoltage Suppression Function ........................................... 144
Overvoltage Suppression Function Selection ............................... 144
ov Suppression Function Selection........................................... 284
P
Parameter Range Setting Error................................................ 213
Parameter Selection Error ..................................................... 215
Parameters for KEB Ride-Thru ............................................... 138
Parameters to Minimize Motor Hunting and Oscillation .................. 177
PASS ............................................................................. 210
Password ...........................................................................12
Password Setting..................................................................12
Peak Hold Current .............................................................. 303
Peak Hold Output Frequency ................................................. 303
PF ................................................................................. 197
PG 1 Division Rate for PG Pulse Monitor ....................................85
PG 1 Gear Teeth 1 ................................................................86
PG 1 Gear Teeth 2 ................................................................86
PG 1 Pulses Per Revolution .....................................................84
PG 1 Rotation Selection .........................................................85
PG 1 Signal Selection ............................................................86
PG 2 Division Rate for PG Pulse Monitor ....................................85
PG 2 Gear Teeth 1 ................................................................86
PG 2 Gear Teeth 2 ................................................................86
PG 2 Pulses Per Revolution .....................................................84
PG 2 Rotation Selection .........................................................85
PG 2 Signal Selection ............................................................86
PG Disconnect (for any control modes using a PG option card) ......... 198
PG Disconnect (for Control Mode with PG) ................................ 210
PG Hardware Fault (detected when using a PG-X3 option card) .. 198, 210
PG Number of Pulses Per Revolution........................................ 169
Index
353