YASKAWA A1000 HHP Programming Manual page 355

Soft Starter Speed Reference at Previous Fault............................. 301
Software Current Limit Selection ............................................ 155
Software No. (PWM)........................................................... 300
Software No. of Master CPU (Flash) ........................................ 300
Software No. of Slave CPU (ROM).......................................... 300
Speed/Torque Control Switchover Time ......................................72
Speed Agree 1 Time Chart .................................................... 107
Speed Agree 2 Time Chart .................................................... 110
Speed Agree Detection Selection............................................. 146
Speed Agreement Detection Level ..................................... 145, 285
Speed Agreement Detection Level (+/-) ............................... 145, 285
Speed Agreement Detection Width .................................... 145, 285
Speed Agreement Detection Width (+/-) .............................. 145, 285
Speed Control Integral Time 1 ................................................ 209
Speed Control Proportional Gain 1........................................... 209
Speed Deviation.......................................................85, 186, 204
Speed Estimation Type Speed Search..........................................28
Speed Feedback Detection Control (AFR) Gain ..................... 158, 290
Speed Feedback Detection Control (AFR) Time Constant 1 ....... 159, 290
Speed Feedback Detection Control (AFR) Time Constant 2 ....... 159, 290
Speed Limit........................................................................71
Speed Limitation..................................................................69
Speed Limit Bias............................................................. 69, 71
Speed Limit Selection ............................................................71
Speed Search Deactivation Current ............................................31
Speed Search Deceleration Time ...............................................31
Speed Search Delay Time .......................................................31
Speed Search Detection Compensation Gain .................................32
Speed Search Method Selection ................................................32
Speed Search Restart Current Level............................................32
Speed Search Restart Detection Time..........................................32
Speed Search Selection at Start .................................................31
Speed Search Wait Time.........................................................33
Stall Prevention ........................................................... 140, 178
Stall Prevention Detection Time.............................................. 145
Stall Prevention Level during Acceleration ........................... 142, 284
Stall Prevention Level during Run ..................................... 144, 284
Stall Prevention Limit during Acceleration ........................... 141, 284
Stall Prevention Selection during Acceleration....................... 140, 284
Stall Prevention Selection during Deceleration....................... 142, 284
Stall Prevention Selection during Run ................................. 143, 284
Station Address Setting Error ................................................. 203
Stator Resistance Error......................................................... 220
STOP button Input.............................................................. 218
STOP Key Function Selection .......................................... 163, 292
Stopping Method after Communication Error ........................ 123, 319
Stopping Method Selection......................................................20
SvE ............................................................................... 199
Switching Between Torque and Speed Control...............................70
T
Target DC Bus Voltage for Overvoltage Suppression and Stall Prevention
..................................................................................... 145
Task Complete .................................................................. 222
Terminal A1 Bias Setting...................................................... 116
Terminal A1 Function Selection.............................................. 115
Terminal A1 Gain Setting ..................................................... 116
Terminal A1 Signal Level Selection ......................................... 115
Terminal A2 Bias Setting...................................................... 117
Terminal A2 Function Selection.............................................. 117
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual
Terminal A2 Gain Setting ..................................................... 117
Terminal A2 Signal Level Selection ......................................... 117
Terminal A3 Bias Setting...................................................... 117
Terminal A3 Function Selection.............................................. 117
Terminal A3 Gain Setting ..................................................... 117
Terminal A3 Signal Level Selection ......................................... 116
Terminal Board Connection Error............................................ 185
Terminal Connections for Communication Self-Diagnostics............. 346
Terminal M1-M2 Function Selection ........................................ 105
Terminal M1-M2 Output Selection ............................................89
Terminal M3-M4 Output Selection ............................................89
Terminal P1-PC Function Selection............................................89
Terminal P2-PC Function Selection............................................89
Terminal P3-PC Output Selection ..............................................89
Terminal P4-PC Output Selection ..............................................89
Terminal P5-PC Output Selection ..............................................89
Terminal P6-PC Output Selection ..............................................89
Terminal V1 Monitor Bias ......................................................88
Terminal V1 Monitor Gain ......................................................88
Terminal V1 Monitor Selection.................................................88
Terminal V1 Signal Level .......................................................88
Terminal V2 Monitor Bias ......................................................88
Terminal V2 Monitor Gain ......................................................88
Terminal V2 Monitor Selection.................................................88
Terminal V2 Signal Level .......................................................88
Thermistor Disconnect ................................................... 199, 211
THo ............................................................................... 199
THo ............................................................................... 211
Timer Function Off-Delay Time................................................33
Timer Function On-Delay Time ................................................33
Too Many Speed Search Restarts............................................. 199
Torque Compensation at Forward Start........................................52
Torque Compensation at Reverse Start ........................................52
Torque Compensation Gain ...............................................51, 176
Torque Compensation Primary Delay Time ............................52, 176
Torque Compensation Primary Delay Time 2 ................................52
Torque Compensation Primary Delay Time Constant 1................... 177
Torque Compensation Primary Delay Time Constant 2................... 177
Torque Compensation Time Constant .........................................52
Torque Control ....................................................................67
Torque Control Block Diagram.................................................68
Torque Control Input Value Selection .........................................68
Torque Control Reference Sources.............................................68
Torque Control Selection ........................................................71
Torque Control Setting Error.................................................. 216
Torque Control Signal Polarity .................................................69
Torque Detection ............................................................... 109
Torque Detection Level 1................................................ 150, 286
Torque Detection Level 2................................................ 150, 286
Torque Detection Selection 1 ........................................... 149, 286
Torque Detection Selection 2 ........................................... 149, 286
Torque Detection Time 1 ................................................ 150, 286
Torque Detection Time 2 ................................................ 150, 286
Torque Limit Control Method Selection during Accel/Decel ...... 152, 287
Torque Limit Enable Time delay at start .................................... 288
Torque Limit Integral Time Constant .................................. 152, 287
Torque Limits ................................................................... 178
Torque Reference ............................................................... 298
Torque Reference/Torque Limit Selection from Comm. Option...........90
Torque Reference at Previous Fault .......................................... 301
Index
355