YASKAWA A1000 HHP Programming Manual page 348

Index
Carrier Frequency Reduction.................................................. 289
Carrier Frequency Reduction Off-Delay Time ............................. 156
Carrier Frequency Reduction Selection...................................... 156
Carrier Frequency Selection.....................................................58
CC-Link Communication Speed................................................91
CC-Link Node Address ..........................................................91
CC-Link Parameters..............................................................91
CE........................................................................... 184, 204
CE Detection Time ....................................................... 124, 320
CF ................................................................................. 185
Coast to stop .......................................................................20
Coast to Stop with Timer ........................................................21
Comm. option card connection error (CN5-A) ............................. 192
Command Messages from Master to Drive ................................. 323
Communication Error .......................................................... 222
Communication Fault Detection Selection ............................ 123, 319
Communication Option Card....................................................89
Communication Option Card Reference..................................... 304
Communication Parity Selection ....................................... 123, 319
Communications Enter Function Selection ........................... 124, 320
Communications Error Operation Selection ..................................90
Communication Speed Selection ....................................... 123, 319
Communications Timing ...................................................... 323
Comparing Parameter Settings................................................ 223
Compressor Application .........................................................16
Connection of a Motor PTC ................................................... 131
Continuous Electrothermal Operation Selection ..................... 132, 282
Control Board Connection Error........................................ 185, 186
Control Circuit Error ..................................................... 185, 186
Control Fault .................................................................... 185
Control Method Selection .......................................................10
Control Method Selection Error .............................................. 214
Control Mode................................................................10, 298
Control Mode Dependent Parameter Default Values ...................... 307
Control Mode Mismatch ....................................................... 222
Control Power Supply Voltage Fault......................................... 201
Converter Heating .............................................................. 194
Conveyor Application............................................................15
Cooling Fan Maintenance ..................................................... 302
Cooling Fan Maintenance Setting (Operation Time) ...................... 293
Cooling Fan Maintenance Time .............................................. 207
Cooling Fan Operation Time.................................................. 302
Cooling Fan Operation Time Setting......................................... 165
CoPy .............................................................................. 222
Copy Allowed Selection ....................................................... 164
Copy Function................................................................... 164
Copy Function Errors .......................................................... 179
Copy Function Selection....................................................... 164
Copy Unit Error ................................................................. 222
CPEr .............................................................................. 222
CPF02 ............................................................................ 185
CPF03 ............................................................................ 185
CPF06 ............................................................................ 185
CPF07 ............................................................................ 185
CPF08 ............................................................................ 185
CPF11 to CPF14 ................................................................ 185
CPF16 to CPF19 ................................................................ 185
CPF20 ............................................................................ 186
CPF21 ............................................................................ 186
CPF22 ............................................................................ 186
348
CPF23 ............................................................................ 186
CPF24 ............................................................................ 186
CPyE ............................................................................. 222
CRC-16 .......................................................................... 324
CRC-16 Checksum Calculation Example ................................... 325
CrST .............................................................................. 204
CSEr .............................................................................. 222
Cumulative Operation Time................................................... 302
Cumulative Operation Time at 5th Most Recent Fault .................... 302
Cumulative Operation Time at Most Recent Fault ......................... 302
Cumulative Operation Time at Previous Fault.............................. 301
Cumulative Operation Time Selection................................. 165, 293
Cumulative Operation Time Setting ................................... 165, 293
Current Alarm ................................................................... 207
Current Detection Error ........................................................ 219
Current Fault .................................................................... 300
Current Unbalance.............................................................. 200
Cyclic Redundancy Check..................................................... 324
D
d3-01.............................................................................. 231
d3-01 through d3-04............................................................ 177
d3-04.............................................................................. 231
d-Axis ACR Output ............................................................ 305
DC Bus Overvoltage ........................................................... 210
DC Bus Pre-Charge Relay Maintenance Setting ........................... 165
DC Bus Undervoltage .......................................................... 200
DC Bus Voltage................................................................. 298
DC Bus Voltage at Previous Fault............................................ 301
DC Bus Voltage Setpoint during KEB....................................... 140
DC Injection Braking Current...................................................26
DC Injection Braking Input Timing Diagram............................... 103
DC Injection Braking Start Frequency.........................................20
DC Injection Braking Time at Start ............................................20
DC Injection Braking Time at Stop ............................................26
DC Injection Braking to Stop ...................................................20
D Control ..........................................................................34
Deceleration Time ................................................................46
Deceleration Time at Stall Prevention during Acceleration......... 141, 285
Defaults by Drive Model Selection (o2-04) and ND/HD (C6-01) ....... 163
Derivative Time (D) ..............................................................37
Desired DC Bus Voltage during KEB ....................................... 283
dEv.......................................................................... 186, 204
DeviceNet Baud Rate Monitor..................................................93
DeviceNet Communication Speed..............................................93
DeviceNet Heartbeat Interval ...................................................94
DeviceNet Idle Mode Fault Detection .........................................93
DeviceNet MAC Address........................................................93
DeviceNet Network MAC ID ...................................................94
DeviceNet Parameters............................................................92
DeviceNet PCA Setting ..........................................................93
DeviceNet PPA Setting ..........................................................93
DeviceNet Scaling Factors ......................................................93
dFAn........................................................................ 187, 205
dFPS .............................................................................. 222
DI-A3 Settings ....................................................................87
Diagnosing and Resetting Faults ............................................. 190
Digital Input Card Settings ......................................................87
Digital Input Option Card Input Selection ....................................87
Digital Input Option DI-A3 Data Length Selection ..........................87
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual